"bridge" GDS output operator; the previous equations were, under
some situations, failing to meet the width requirement. Also:
corrected the "cif style" check so that it does not claim that a
style name with an exact match is ambiguous. Also: Corrected the
use of "grid limit", so that the limit correctly scales with the
output expander value.
cell def that is marked for a "full dump" from a referenced GDS
file. This change was supposed to have been done a few commits
ago but did not work as advertised.
asymmetric MOSFET definitions in the tech file "extract" section.
Corrected the nmos.tech.in file to put the resistance classes in
plane order, as otherwise the interpretation of which resistance
classes belongs to the transistor source and drain can get messed
up by the presence of buried contacts.
magic database derived layout of a cell that declares GDS_FILE
but for which the GDS file referenced cannot be found or read.
This will produce an incomplete GDS file instead of an apparently
good and complete GDS file that actually contains bad data. Also:
Added new command "random" that allows a random seed to be set,
for use with the GDS output when writing a full dump of a GDS
file. Otherwise, the output prefixes are always the same, which
defeats the purpose of adding the random prefix.
significant amounts of time even though there is no display to
receive the result. However, the "suspendall" command only works
if a window exists. The obvious solution is to set GrDisplayStatus
to DISPLAY_SUSPEND whenever magic is run with the "-dnull" option.
This should help speed up a lot of scripts, in particular where
designs are large.
restricted to its original intent, which is to replace the long name
formed from the plane short name and the "minfinity" coordinate.
This avoids issues with conflicting substrate names derived from a
real layer such as pwell. Also, the global substrate node name now
returns the variable name without the "$" in front if the variable
has not been set to anything. This avoids potential syntax errors
in the netlist.
that have been removed by flattening into the parent cell due to lack
of devices. Previously the checks on writing the subcircuit and writing
the call were slightly different, leading to instances in which the
subcircuit call would be written to the netlist output without the
subcircuit being defined. (2) Corrected an error in the "bridge" CIF/GDS
output operator. In certain (somewhat rare) geometries, the tile behind
(instead of in front of) the corner being checked may be incorrectly
flagged as a DRC spacing error. The fix is to ignore tiles that are
behind the corner being checked.
of input cells on a per-cellname basis, using glob-style pattern
matching. This is probably the best way to deal with 3rd-party vendor
GDS with unfortunate practices like dividing devices up among cells in
a hierarchy, even though it comes across as a bit of a hack solution.
one terminal of a device as the substrate, but also specifies
shielding types for the substrate, then the extraction cannot just
assume that a missing terminal is connected to the substrate without
first checking that there are no substrate shielding types under the
device.
Corrected the "lef write -hide" command option so that obstructions
outside of the boundary are included in the obstruction list, in
addition to the block inside. This had previously been done
correctly for use with the "setback" option but would fail only
for setback = 0.
tech file format "version" section. This can be used to specify the
version of magic that must be used to be compatible with the tech file.
This effectively supercedes the technology version number. (2) Changed
the behavior of "make" to set the version and revision numbers on doing
"make" instead of "configure". This allows the version to update
correctly after doing a "git pull" followed by "make" without doing
"configure" in between. (3) Fixed a couple of issues that were flagged
as compile-time warnings.
true, this will force the "gds write" command to write out creation
date stamps as zero. This is very useful for avoiding changing the
contents of an otherwise-unchanged layout, especially if it is in
a git repository where it will force the entire file to be replaced.
layers that are normally automatically generated to be supplemented
with additional geometry in the form of properties. The first
commit implements a CIF operator "mask-hints" that tells CIFGenLayer
that additional geometry may be specified with a property named
"MASKHINTS_" plus the name passed to the operator as its only
argument. A more extensive commit to be done will allow this
operator to be used on cifinput to use mask hints to retain the
exact geometry of mask layers used in the input file.
to allow a cell to be flushed with dereferencing (i.e., discard any file
path attached to the cell, and use the search paths to find the cell when
it is reloaded).
routine attempts to rescale the contents of the top-level cell after
moving forward in the GDS to find a cell that was used before it was
defined, if reading that cell caused the scale to change. However,
the numerator and denominator were reversed, causing the scaling to
be the inverse of what it should have been.
Ghazy) to read pin uses from a DEF file, including the three types
that are not defined by the LEF format (go figure). Expanded the
bitmask of label flags to include the additional use types. Also
shifted the label flag bitmask up to make additional room for more
port number, as there is no point in having unused bits in the
bitmask.
could have multiple ports of the same name. This problem had been
worked over before, but there was an indpendent mechanism producing
the same result for a completely different reason, caused by subcells
being much larger than the cookie-cutter extraction method's extraction
regions. Solved by tracking port names in a hash table and preventing
re-use. (2) ext2spice was producing "no such node" errors; like (1)
this had been previously worked on, and like (1) this mechanism was
independent. Problem came from not passing -1 to extHierSubstrate for
the non-arrayed dimension of a 1-dimensional array. Also: Removed
the word "fatal" from extraction error reporting, as nearly all
extraction errors are entirely benign. This should clear up confusion
among alarmed end-users.
occurrence of the label to place the box on. This can be used with
"findlabel -glob <name>" to get a list of labels and determine the
length of the list, and then iterate through each occurrance of the
label in the edit cell.
disagreements between parent and child cells on GDS generation for
templayers, as these layers are not output; any resulting differences
showing up eventually on an output layer will be reported.
bloat-all, that was resetting flags in the entire plane within the
callback for each tile processed. This would push DRC run-times from
minutes to hours. Also corrected another, much more minor, efficiency,
in which the connection mask was generated in the callback routine
for each tile, instead of calculating before the plane search and
passing the mask to the callback function in the client data.
hierarchical processing from CIFGenSubcells() and CIFGenArrays(), and to
avoid certain operators that are useless and harmful when applied
hierarchically; namely squares, slots, bbox, boundary, and net.
the handling of subcell instances generally. Previously it would check
the interaction between neighboring cells in an array without regard to
any material in the parent cell which might remove those errors;
consequently, the array would have to be DRC clean by itself in order for
the parent cell to show as DRC clean. The array check has been moved
inside the DRCInteractionCheck() routine, so that it runs only where
arrayed instances do not interact with anything else. Within interaction
areas, the area is flattened and checked, so the array check is not
needed.
unique" code. It was using DBEraseLabelsByContent() which would
erase all matching labels, and could potentially erase labels that
were still remaining on the list being processed, causing a segfault.
Also corrected minor errors identified by valgrind during debugging
the above-referenced problem.
Instead of a 6-character suffix generated randomly, the 6-character
suffix is generated by a hash algorithm from the device parameters.
If the cell parameters are changed, then the cell itself changes.
If the instance name was default (derived from the cell name) then
the instance name changes accordingly. The result is that there
cannot be two (auto-)generated cells with the same parameters but
with different cell names.
which was failing to clear tiles in the layout of the "processed" state,
leading to unpredicatable results if the same layout layer is used in
a subsequent CIF operation.
from child cells, which was incorrectly descending all the way down
into the hierarchy; not only can this produce the incorrect result
but it also wastes time searching cells that don't need to be
searched.
are interpreted in the dimensions used in the cifoutput section rather
than always in centimicrons (otherwise, rules at, say, 5nm cannot be
represented in the DRC section).
read". While "lef read" normally annotates existing layout, this
option ensures that no additional cells are created from macros in
the input LEF file. (2) Added a check on the "Input off lambda grid"
warning during CIF/GDS input such that it is not repeated once issued,
as it tends to be output many times when it occurs.
from the layout window. The main reason for this is to keep the
box out of the image when doing "plot svg". The "plot" command was
also modified to always do a plot of the entire cell in the active
layout window if the box is not present.
bounding box of the selection (somewhat unuseful, especially as the
result gets absorbed by the tag callback), and "box select", which
sets the cursor box to the bounding box of the selection (much more
useful). Also corrected the "port" command so that the command
"port make" will search only for non-port labels.
command when annotating an existing layout from a LEF database, if
there is a port in the layout that is shadowed by a label with the
same name that is not a port.
device layer type to describe the extraction for both a regular FET
and an extended-drain device. Note that the current code still
requires that the extended-drain device be declared first, and does
not check for this or attempt to reorder if incorrect.
easier to scan through a cell's ports. Used that capability in the
"readspice" script to handle case sensitivity problems, and to find
labels that are not ports and force them to be ports to match the
reference netlist.
Tcl_Alloc() and Tcl_Free() because Tcl_Alloc() uses (unsigned int)
for the argument type and therefore limits memory allocations to
what can fit in 32 bits. Using the system malloc(size_t) should not
cause any issues.
port labels that are unnattached ("attached" to space), or possibly
sticky labels without any geometry underneath, end up with a NULL
node during EFBuild().
to accomodate a method used for processes that require additional
spacing between contacts for large via arrays; this requires
distinguishing between large and small areas to output vias, and
so requires use of "and" and "and-not" before "squares". This
highlights the arbitrary nature of this routine, which probably
works better getting data from cifinput, or not at all (i.e., it is
used when reading LEF, but it is known that the LEF read routines
would be better implemented by running input through CIFGen(). If
that were done, then this problem would not come up).
caption line in the GUI window, which was causing problems with
long filenames overrunning the string array dedicated to the caption
line. Thanks to Sylvain Munaut for the patch.
supposed to pull "sticky labels" into the cumulative flattened
layout. Because it failed to check for the "sticky" flag, it
would copy all labels, causing extraction time to go exponential
as the number of labels in the design increases. Based on this
correction, the extHierConnectFunc1() routine should be able to
be optimized by stopping the search for sticky labels on the first
non-sticky label, since extSubtreeFunc() ensures that all sticky
labels come first in the label list.
command fails for the tutorial tut3d cell due to a missing
initialization of the cd_cellPlane record in DBCellCopyDefBody().
This was missed in the implementation of "bplane", and was not
checked because the routine is only called from the "plow" command
routines.
for geometry on MASTERSLICE layers (which was inadvertantly broken),
and (2) Added option "lef write -toplayer", which outputs pin geometry
only for the topmost layer belonging to a pin, with connected layers
underneath being designated as obstructions.
(scrollbar, title bar, etc.) from the output if the command is
called from the non-GUI-wrapper environment (where the border area
is part of the rendered output). This was required due to an
unsolved bug in which calling magic to write SVG output from the
wrapper in some pathological case exposed a Tk bug that caused
the Tk grid manager to infinite loop, filling memory without
limit.
in-line comment character recognized by ngspice (which has changed
since the version of the documentation I had, which supported the
use of the character ';', which was what magic was using).
"lef write", which had one typo in the formatting, plus was using
a static string method for generating the formatted output that was
implementation-dependent on fprintf(). These have been fixed.
minimum manufacturing grid (normally 1000 but can be altered by the
"angstroms" flag in the cifoutput section, and by "gridlimit").
The output values then are truncated such that the floating-point
output value, when multiplied by the UNITS value, is always an
integer. e.g., "gridlimit 5" will change UNITS to 200, and values
will be minimum precision 0.005, or 5 nanometers.
generation in the "cifoutput" section of the techfile. This operator
solves the problems with the catecorner position of geometry when
attempting to automatically close up gaps between islands of a layer.
could cause serious errors on systems that do not auto-zero allocated
memory. Also: Fixed an error introduced by a recent commit to allocate
character memory for efReadLine() which frees the memory before reading
a .res.ext file, causing a crash when using "ext2spice" with the
"extresist on" option.
memory for the input line instead of using a fixed 1024-character
buffer. That avoids the issue of rare but possible overflow when
reading a .ext file with unknown line lengths.
optional name field to the "substrate" line in the extract section
of the techfile. This is the default name of the substrate if not
connected to anything labeled. It may use a Tcl variable (preferred).
(2) Added command option "instance orientation [-def]" that returns
the orientation of the named or selected instance. The -def option
returns the orientation using DEF naming convention; otherwise, the
naming used with "getcell" is generated.
SPICE subcircuit definitions from a netlist file and apply the port
order in the netlist to the port labels in the corresponding cell
or cells in the magic database. Also: Corrected an error in the
bloat-all code introduced in a recent commit that can cause a
segfault.
templayers. This permits some useful interactions like growing to
the size of a bounding box, or abutment box, as well as many other
possibilities. Also: Corrected the use of "cif see" for the boundary
(abutment box) layer, which was not working because the "cif see"
command uses a flattened CellDef that does not have the boundary
property of the cell it was flattened from.
of cell name dereferencing on file loads, where the cell load
subroutine call ended up with the wrong number of arguments,
resulting in an invalid pointer and a crash condition.
"ignore-unknown-layer-labels" is set, then error messages will not
be displayed when labels in the GDS input are on unknown layers
(this option is and has been otherwise handled correctly; the only
issue is the generation of an error message on the output).
unrecognized layers when the "readonly" read option is set.
Added support to scale elements (from the "element" command,
such as the measurement text and arrows) when the grid scales,
which was missing. Corrected the output of persistent elements
in a .mag file so that they are correctly scaled by the scale
reducer.
a LEF macro that has parentheses around the coordinates. Weirdly,
this is requires by the LEF/DEF spec, but is rarely if ever seen
in actual LEF files. Go figure.
GDS of abstract views, such that if the cellname being dumped is the
same as the library name, then no prefix is added to subcells. This
behavior may be changed in the future.
Conflicts:
VERSION
database/DBcellsrch.c
database/DBconnect.c
extract/ExtInter.c
lef/Depend
utils/Depend
Updated bplane branch with all changes to master since the bplane branch
was last modified.
uninitialized variable, with the result that writing GDS would
claim that it cannot scale down enough and that the output units
are either wrong or the output style must have "units angstroms".
Using angstrom units would solve the problem but did not treat
the root of the problem.
which had been changed a few months back to remove the individual
cell count and only list the top level cell. The behavior has been
changed a bit so that "list" returns values for the top level cell
only, but "listall" returns a complete list. "drc list count total"
gives the DRC count for the top cell, but "drc listall count total"
gives the DRC count for everything (probably not very useful).
Also: Implemented a behavior by request to automatically removed
the (UNNAMED) cell whenever a new cell is loaded and the (UNNAMED)
cell has not been modified.
force an update of the repository, which caused the script handling
the tarball generation and mirror to github to be hosed, which I did
not notice for three weeks.
Tim Edwards
Tim Edwards
Chuan Chen