This fixes crash on macos due to wrong hash() being linked in.
It also makes sure that proper function defs are declared and available
(as required by C99) to make compile possible in newer compilers (e.g.
Apple clang) and to some extend prevent similar linkage issues happening
again.
class during setup, for the purpose of generating some derived
value that is used for merging and sorting, such as area = l*w.
Note that this likely needs adjusting so that the expression is
evaluated but not replaced for the purpose of sorting, since the
values to the parameter may change after parallel and series
merging.
can be turned on or off from the setup using "property parallel open"
to allow parallelizing devices with no-connect pins vs. "property
parallel connected" to only allow parallelizing of devices with all
pins connected.
handle verilog syntax. Also: Added SPICE voltage and current
sources as separate classes (as opposed to being converted to
subcircuits, which was how they were previously handled). That
allowed voltage sources to be checked for zero value and removed
by shorting the ends together, as was being done for zero value
resistors (note that like zero-value resistors, removal is only
done if removing the component makes a better match than leaving
it in). In particular, yosys has SPICE netlist output that
converts equality assignments ("assign a = b") into zero-value
voltage sources, so these components need to be treated as
non-physical elements.
the possibility that a device (e.g., resistor or capacitor) may
not be a semiconductor device (in other words, a parasitic or
ideal device), and therefore uses "value" but not width and
length, and therefore "value" is a critical property to merge
both in series and parallel. Corrected the series/parallel
network optimization to prevent it from setting both M and S
records > 1 on the same device (which is ambiguous). To try
to get number of devices to match, where there are both series
and parallel devices, they will be merged across the critical
property early (before property matching).
some problems stemming from comparing a case-sensitive netlist
against a case-insensitive one. Verilog netlist reading does
not yet have support for macros other than "`include", and it
does not yet have support for bit vectors constructed with
braces ({}).
treat empty subcircuits as blackbox cells automatically without
requiring specific callse to "model <cell> blackbox" for each.
Enabled in LVS script by giving option "-blackbox" at the end
of the LVS command.
making any subcircuit serializable by using the new command option
"property (device) serial|parallel enable|disable". Note that as
of this commit, serial device detection is enabled but serial
networks are not collapsed for matching, which will tend to lead
to property errors in serial devices until this code is added,
which should be in a day or two.
as failing on certain compilers. This undoubtedly reflects some
change in gcc or the OS setup, but since modern compilers should
be able to figure out for themselves when to inline a subroutine
(or not), the inline hint is somewhat arcane and unnecessary.
include calculations of effective width due to the addition of
width of multiple device instances in parallel. The original
behavior of splitting all "M=" devices into individual instances
has been effectively inverted, instead combining all parallel
devices of the same class into one, with multiple property
records for devices with non-matching properties (e.g., width,
length, etc.). Property matching combines devices with different
"critical properties" (e.g., FET gate width) if these are defined
in the setup using the "property merge" command.
Not yet done: Matching of multiple property records when
critial properties are not defined, handling of critical properties
that combine in parallel instead of simple addition, handling of
devices that combine in series, and the combination of non-critical
properties (e.g., source and drain area, although these are usually
removed from matching).
based on properties that can be traded with number of devices,
such as MOSFET width, by merging. This initial implementation
is somewhat limited, only dealing with properties that merge
by summing. Only devices that do not match at all in the other
circuit will be considered for merging. The feature includes
a command option "property ... merge ..." that allows control
over which devices can and cannot be merged.
variables to iterate over hash table contents. This led to the
inability to nest hash table iterators. Fixed by defining a
wrapper structure that holds the actual hash table plus the size
and iterator indexes. Not only does this solve the nesting
problem, but it also avoids the need to pass the hash table size
on every call, and that reduces the number of ways a hash table
subroutine can go wrong (e.g., cannot access the table out of
bounds simply by passing a size that is larger than was used to
initialize the table).
Kamyar Mohajerani
Tim Edwards
Alessandro De Laurenzis