322 lines
22 KiB
Plaintext
322 lines
22 KiB
Plaintext
1 DmpCeff.cc:1589 cell %s delay model not supported on SPF parasitics by DMP delay calculator
|
|
8 ConcreteNetwork.cc:1867 cell type %s can not be linked.
|
|
9 Sdc.cc:2465 No common period was found between clocks %s and %s.
|
|
10 Genclks.cc:289 no master clock found for generated clock %s.
|
|
11 Genclks.cc:331 generated clock %s is in the fanout of multiple clocks.
|
|
13 Genclks.cc:990 generated clock %s source pin %s missing paths from master clock %s.
|
|
15 Sim.cc:861 propagated logic value %c differs from constraint value of %c on pin %s.
|
|
16 Sta.cc:2010 '%s' is not a valid startoint.
|
|
17 Sta.cc:2085 '%s' is not a valid endpoint.
|
|
21 SpefParse.yy:805 %d is not positive.
|
|
22 SpefParse.yy:814 %.4f is not positive.
|
|
23 SpefParse.yy:820 %.4f is not positive.
|
|
24 WritePathSpice.cc:425 pg_pin %s/%s voltage %s not found,
|
|
25 WritePathSpice.cc:432 Liberty pg_port %s/%s missing voltage_name attribute,
|
|
26 WritePathSpice.cc:962 %s pg_port %s not found,
|
|
27 WritePathSpice.cc:1016 no register/latch found for path from %s to %s,
|
|
28 WritePathSpice.cc:1383 The following subkcts are missing from %s
|
|
29 WritePathSpice.cc:1441 subckt %s port %s has no corresponding liberty port, pg_port and is not power or ground.
|
|
160 Sta.cc:2007 '%s' is not a valid startpoint.
|
|
161 Sta.cc:2082 '%s' is not a valid endpoint.
|
|
162 VerilogReader.cc:1750 %s is not a verilog module.
|
|
163 VerilogReader.cc:1755 %s is not a verilog module.
|
|
179 SpefReader.cc:723 %s.
|
|
204 StaTcl.i:4118 POCV support requires compilation with SSTA=1.
|
|
207 GraphDelayCalc1.cc:746 port not found in cell
|
|
208 Graph.cc:744 arc_delay_annotated array bounds exceeded
|
|
209 Graph.cc:759 arc_delay_annotated array bounds exceeded
|
|
210 Graph.cc:771 arc_delay_annotated array bounds exceeded
|
|
211 SdcNetwork.cc:1026 inst path string lenth estimate busted
|
|
212 SdcNetwork.cc:1098 inst path string lenth estimate exceeded
|
|
213 Sdc.cc:4181 group path name and is_default are mutually exclusive.
|
|
214 WriteSdc.cc:1332 unknown exception type
|
|
215 WriteSdc.cc:1903 illegal set_logic value
|
|
216 WriteSdc.cc:1947 invalid set_case_analysis value
|
|
228 Graph.cc:784 arc_delay_annotated array bounds exceeded
|
|
251 PathEnumed.cc:126 enumerated path required time
|
|
252 PathEnumed.cc:135 enumerated path required time
|
|
253 PathGroup.cc:402 unknown path end type
|
|
254 PathVertexRep.cc:144 tag group missing tag
|
|
255 ReportPath.cc:290 unsupported path type
|
|
256 ReportPath.cc:311 unsupported path type
|
|
257 ReportPath.cc:354 unsupported path type
|
|
258 ReportPath.cc:2354 generated clock pll source path too short.
|
|
259 ReportPath.cc:2532 unsupported path type
|
|
260 Search.cc:2659 max tag group index exceeded
|
|
261 Search.cc:2885 max tag index exceeded
|
|
262 Search.cc:3570 unexpected filter path
|
|
263 Search.cc:3738 tns incr existing vertex
|
|
264 Sta.cc:3877 corresponding timing arc set not found in equiv cells
|
|
265 TagGroup.cc:330 tag group missing tag
|
|
300 Util.tcl:218 no commands match '$pattern'.
|
|
301 Power.tcl:223 activity should be 0.0 to 1.0 or 2.0
|
|
302 Power.tcl:231 duty should be 0.0 to 1.0
|
|
303 Cmds.tcl:552 -clock ignored for clock objects.
|
|
304 Cmds.tcl:756 -from/-to keywords ignored for lib_pin, port and pin arguments.
|
|
305 Cmds.tcl:1038 object '$obj' not found.
|
|
313 Cmds.tcl:1707 unsupported object type $object_type.
|
|
315 Cmds.tcl:1728 $arg_name '$object_type' is not a net.
|
|
316 Cmds.tcl:1733 $arg_name '$arg' not found.
|
|
318 Search.tcl:379 unknown path group '$name'.
|
|
319 Sdc.tcl:277 $unit scale [format %.0e $scale] does not match library scale [format %.0e $unit_scale].
|
|
320 Sdc.tcl:478 current_design for other than top cell not supported.
|
|
321 Sdc.tcl:515 patterns argument not supported with -of_objects.
|
|
322 Sdc.tcl:550 instance '$pattern' not found.
|
|
323 Sdc.tcl:611 clock '$pattern' not found.
|
|
324 Sdc.tcl:638 positional arguments not supported with -of_objects.
|
|
325 Sdc.tcl:664 library '$lib_name' not found.
|
|
326 Sdc.tcl:676 cell '$cell_pattern' not found.
|
|
327 Sdc.tcl:723 library/cell/port '$pattern' not found.
|
|
328 Sdc.tcl:743 port '$port_pattern' not found.
|
|
329 Sdc.tcl:748 library '$lib_name' not found.
|
|
330 Sdc.tcl:758 -nocase ignored without -regexp.
|
|
331 Sdc.tcl:784 library '$pattern' not found.
|
|
332 Sdc.tcl:847 patterns argument not supported with -of_objects.
|
|
333 Sdc.tcl:871 net '$pattern' not found.
|
|
334 Sdc.tcl:900 patterns argument not supported with -of_objects.
|
|
335 Sdc.tcl:937 pin '$pattern' not found.
|
|
336 Sdc.tcl:994 patterns argument not supported with -of_objects.
|
|
337 Sdc.tcl:1008 port '$pattern' not found.
|
|
338 Sdc.tcl:1109 adjusting non-increasing clock -waveform edge times.
|
|
339 Sdc.tcl:1113 -waveform time greater than two periods.
|
|
341 Sdc.tcl:1471 extra positional argument $arg.
|
|
342 Sdc.tcl:1504 -clock ignored for clock objects.
|
|
343 Sdc.tcl:1550 set_sense -type data not supported.
|
|
344 Sdc.tcl:1565 set_clock_sense is deprecated as of SDC 2.1. Use set_sense -type clock.
|
|
345 Sdc.tcl:1577 -pulse argument not supported.
|
|
346 Sdc.tcl:1586 -positive, -negative, -stop_propagation and -pulse are mutually exclusive.
|
|
347 Sdc.tcl:1599 hierarchical pin '[get_full_name $pin]' not supported.
|
|
348 Sdc.tcl:1801 -from/-to keywords ignored for lib_pin, port and pin arguments.
|
|
349 Sdc.tcl:1469 unknown keyword argument $arg.
|
|
350 Sdc.tcl:1949 -from, -through or -to required.
|
|
351 Sdc.tcl:2028 -source_latency_included ignored with -reference_pin.
|
|
352 Sdc.tcl:2031 -network_latency_included ignored with -reference_pin.
|
|
353 Sdc.tcl:2050 $cmd not allowed on [pin_direction $pin] port '[get_full_name $pin]'.
|
|
354 Sdc.tcl:2052 $cmd relative to a clock defined on the same port/pin not allowed.
|
|
355 Sdc.tcl:2095 '$args' ignored.
|
|
356 Sdc.tcl:2225 '$args' ignored.
|
|
357 Sdc.tcl:2272 virtual clock [get_name $clk] can not be propagated.
|
|
358 Sdc.tcl:2421 -multiply_by ignored.
|
|
359 Sdc.tcl:2424 -dont_scale ignored.
|
|
360 Sdc.tcl:2427 -no_design_rule ignored.
|
|
361 Sdc.tcl:2468 -clock not supported.
|
|
362 Sdc.tcl:2471 -clock_fall not supported.
|
|
363 Sdc.tcl:2517 -pin_load not allowed for net objects.
|
|
364 Sdc.tcl:2520 -wire_load not allowed for net objects.
|
|
365 Sdc.tcl:2523 -rise/-fall not allowed for net objects.
|
|
366 Sdc.tcl:2656 -data_path, -clock_path, -rise, -fall ignored for ports and designs.
|
|
367 Sdc.tcl:2726 derating factor greater than 2.0.
|
|
368 Sdc.tcl:2763 -cell_delay and -cell_check flags ignored for net objects.
|
|
369 Sdc.tcl:2822 no valid objects specified for $key.
|
|
370 Sdc.tcl:2855 no valid objects specified for $key
|
|
371 Sdc.tcl:3016 set_wire_load_min_block_size not supported.
|
|
372 NetworkEdit.tcl:80 connect_pins is deprecated. Use connect_pin.
|
|
400 Util.tcl:44 $cmd $key missing value.
|
|
401 Util.tcl:61 $cmd $key missing value.
|
|
402 Util.tcl:71 $cmd $arg is not a known keyword or flag.
|
|
403 Util.tcl:93 $cmd $arg is not a known keyword or flag.
|
|
404 Util.tcl:191 Usage: $cmd $cmd_args($cmd)
|
|
405 Util.tcl:193 Usage: $cmd argument error
|
|
406 Util.tcl:308 $cmd positional arguments not supported.
|
|
407 Util.tcl:314 $cmd requires one positional argument.
|
|
408 Util.tcl:321 $cmd requires zero or one positional arguments.
|
|
409 Util.tcl:327 $cmd requires two positional arguments.
|
|
410 Util.tcl:334 $cmd requires one or two positional arguments.
|
|
411 Util.tcl:340 $cmd requires three positional arguments.
|
|
412 Util.tcl:346 $cmd requires four positional arguments.
|
|
413 Util.tcl:354 $cmd_arg '$arg' is not a float.
|
|
414 Util.tcl:360 $cmd_arg '$arg' is not a positive float.
|
|
415 Util.tcl:366 $cmd_arg '$arg' is not an integer.
|
|
416 Util.tcl:372 $cmd_arg '$arg' is not a positive integer.
|
|
417 Util.tcl:378 $cmd_arg '$arg' is not an integer greater than or equal to one.
|
|
418 Util.tcl:384 $cmd_arg '$arg' is not between 0 and 100.
|
|
419 Sta.tcl:120 report_clock_skew -setup and -hold are mutually exclusive options.
|
|
420 Sta.tcl:195 $cmd -path_delay must be min, min_rise, min_fall, max, max_rise, max_fall or min_max.
|
|
421 Sta.tcl:205 $cmd command failed.
|
|
422 Sta.tcl:224 -endpoint_count must be a positive integer.
|
|
423 Sta.tcl:232 -group_count must be a positive integer.
|
|
424 Sta.tcl:263 '$arg' is not a known keyword or flag.
|
|
425 Sta.tcl:265 positional arguments not supported.
|
|
426 Sta.tcl:430 analysis type single is not consistent with doing both setup/max and hold/min checks.
|
|
427 Sta.tcl:435 positional arguments not supported.
|
|
428 Sta.tcl:864 set_assigned_transition transition is not a float.
|
|
429 Sdf.tcl:47 -analysis_type must be single, bc_wc or on_chip_variation
|
|
430 Sdf.tcl:60 -cond_use min_max cannot be used with analysis type single.
|
|
431 Sdf.tcl:108 $key must be sdf_min, sdf_typ, or sdf_max.
|
|
432 Sdf.tcl:210 SDF -divider must be / or .
|
|
433 Parasitics.tcl:46 path instance '$path' not found.
|
|
434 Parasitics.tcl:63 -reduce_to must be pi_elmore or pi_pole_residue2.
|
|
435 DelayCalc.tcl:120 delay calculator $alg not found.
|
|
436 Variables.tcl:45 sta_report_default_digits must be a positive integer.
|
|
437 Variables.tcl:70 sta_crpr_mode must be pin or transition.
|
|
438 Variables.tcl:187 $var_name value must be 0 or 1.
|
|
439 Cmds.tcl:117 unsupported object type $list_type.
|
|
440 Cmds.tcl:139 -from/-to arguments not supported with -of_objects.
|
|
441 Cmds.tcl:277 unsupported -filter expression.
|
|
442 Cmds.tcl:295 $cmd missing -from argument.
|
|
443 Cmds.tcl:300 $cmd missing -to argument.
|
|
444 Cmds.tcl:305 $cmd delay is not a float.
|
|
445 Cmds.tcl:310 set_annotated_delay -cell and -net options are mutually excluive.
|
|
446 Cmds.tcl:316 $cmd pin [get_full_name $pin] is not attached to instance [get_full_name $inst].
|
|
447 Cmds.tcl:321 $cmd pin [get_full_name $pin] is not attached to instance [get_full_name $inst]
|
|
448 Cmds.tcl:326 $cmd -cell or -net required.
|
|
449 Cmds.tcl:384 $cmd missing -from argument.
|
|
450 Cmds.tcl:393 $cmd -clock must be rise or fall.
|
|
451 Cmds.tcl:400 $cmd missing -to argument.
|
|
452 Cmds.tcl:415 $cmd missing -setup|-hold|-recovery|-removal check type..
|
|
453 Cmds.tcl:423 $cmd check_value is not a float.
|
|
454 Cmds.tcl:503 the -all and -name options are mutually exclusive.
|
|
455 Cmds.tcl:506 either -all or -name options must be specified.
|
|
456 Cmds.tcl:514 one of -logically_exclusive, -physically_exclusive or -asynchronous is required.
|
|
457 Cmds.tcl:517 the keywords -logically_exclusive, -physically_exclusive and -asynchronous are mutually exclusive.
|
|
458 Cmds.tcl:564 -source '[$pin path_name]' is not a clock pin.
|
|
459 Cmds.tcl:622 -from/-to must be used together.
|
|
460 Cmds.tcl:642 -rise, -fall options not allowed for single clock uncertainty.
|
|
461 Cmds.tcl:677 missing -from, -rise_from or -fall_from argument.
|
|
462 Cmds.tcl:689 missing -to, -rise_to or -fall_to argument.
|
|
463 Cmds.tcl:808 -from/-to hierarchical instance not supported.
|
|
464 Cmds.tcl:850 $cmd command failed.
|
|
465 Cmds.tcl:857 positional arguments not supported.
|
|
466 Cmds.tcl:861 -from, -through or -to required.
|
|
467 Cmds.tcl:980 unsupported object type $object_type.
|
|
468 Cmds.tcl:1271 $corner_name is not the name of process corner.
|
|
469 Cmds.tcl:1276 -corner keyword required with multi-corner analysis.
|
|
470 Cmds.tcl:1291 $corner_name is not the name of process corner.
|
|
471 Cmds.tcl:1296 missing -corner arg.
|
|
472 Cmds.tcl:1307 $corner_name is not the name of process corner.
|
|
473 Cmds.tcl:1323 $corner_name is not the name of process corner.
|
|
474 Cmds.tcl:1348 both -min and -max specified.
|
|
475 Cmds.tcl:1362 both -min and -max specified.
|
|
476 Cmds.tcl:1389 only one of -early and -late can be specified.
|
|
477 Cmds.tcl:1395 -early or -late must be specified.
|
|
478 Cmds.tcl:1402 both -early and -late specified.
|
|
479 Cmds.tcl:1417 $arg_name must be a single library.
|
|
480 Cmds.tcl:1423 $arg_name type '$object_type' is not a library.
|
|
481 Cmds.tcl:1428 library '$arg' not found.
|
|
482 Cmds.tcl:1445 $arg_name must be a single lib cell.
|
|
483 Cmds.tcl:1501 $arg_name must be a single instance.
|
|
484 Cmds.tcl:1507 $arg_name type '$object_type' is not an instance.
|
|
485 Cmds.tcl:1512 instance '$arg' not found.
|
|
486 Cmds.tcl:1531 $arg_name type '$object_type' is not an instance.
|
|
487 Cmds.tcl:1538 instance '$arg' not found.
|
|
488 Cmds.tcl:1599 $arg_name type '$object_type' is not a pin or port.
|
|
489 Cmds.tcl:1606 pin '$arg' not found.
|
|
490 Cmds.tcl:1626 $arg_name type '$object_type' is not a port.
|
|
491 Cmds.tcl:1830 $cmd object is null.
|
|
492 Cmds.tcl:1835 $cmd $type_key must be specified with object name argument.
|
|
493 Cmds.tcl:1878 get_property $object is not an object.
|
|
494 Cmds.tcl:1901 $object_type not supported.
|
|
495 Cmds.tcl:1904 $object_type '$object_name' not found.
|
|
496 Cmds.tcl:1978 Directory $spice_dir not found.
|
|
497 Cmds.tcl:1981 $spice_dir is not a directory.
|
|
498 Cmds.tcl:1984 Cannot write in $spice_dir.
|
|
499 Cmds.tcl:1987 No -spice_directory specified.
|
|
500 Cmds.tcl:1993 -lib_subckt_file $lib_subckt_file is not readable.
|
|
501 Cmds.tcl:1996 No -lib_subckt_file specified.
|
|
502 Cmds.tcl:2002 -model_file $model_file is not readable.
|
|
503 Cmds.tcl:2005 No -model_file specified.
|
|
504 Cmds.tcl:2011 No -power specified.
|
|
505 Cmds.tcl:2017 No -ground specified.
|
|
506 Cmds.tcl:2021 No -path_args specified.
|
|
507 Cmds.tcl:2026 No paths found for -path_args $path_args.
|
|
508 Search.tcl:146 -min and -max cannot both be specified.
|
|
509 Search.tcl:166 pin '$pin_arg' is hierarchical.
|
|
510 Search.tcl:232 -format $format not recognized.
|
|
511 Sdc.tcl:64 cannot open '$filename'.
|
|
512 Sdc.tcl:116 incomplete command at end of file.
|
|
513 Sdc.tcl:202 hierarchy separator must be one of '$sdc_dividers'.
|
|
514 Sdc.tcl:248 unknown unit $unit '$suffix'.
|
|
515 Sdc.tcl:321 unknown $unit unit '$suffix'.
|
|
516 Sdc.tcl:584 unsupported -filter expression.
|
|
517 Sdc.tcl:969 unsupported -filter expression.
|
|
518 Sdc.tcl:1045 unsupported -filter expression.
|
|
519 Sdc.tcl:1078 -add requires -name.
|
|
520 Sdc.tcl:1083 -name or port_pin_list must be specified.
|
|
521 Sdc.tcl:1091 missing -period argument.
|
|
522 Sdc.tcl:1097 -waveform edge_list must have an even number of edge times.
|
|
523 Sdc.tcl:1154 empty ports/pins/nets argument.
|
|
524 Sdc.tcl:1162 -add requires -name.
|
|
525 Sdc.tcl:1167 name or port_pin_list must be specified.
|
|
526 Sdc.tcl:1174 missing -source argument.
|
|
527 Sdc.tcl:1191 -master_clock argument empty.
|
|
528 Sdc.tcl:1194 -add requireds -master_clock.
|
|
529 Sdc.tcl:1198 -multiply_by and -divide_by options are exclusive.
|
|
530 Sdc.tcl:1202 -divide_by is not an integer greater than one.
|
|
531 Sdc.tcl:1205 -combinational implies -divide_by 1.
|
|
532 Sdc.tcl:1210 -multiply_by is not an integer greater than one.
|
|
533 Sdc.tcl:1216 -duty_cycle is not a float between 0 and 100.
|
|
534 Sdc.tcl:1222 -edges only supported for three edges.
|
|
535 Sdc.tcl:1228 edges times are not monotonically increasing.
|
|
536 Sdc.tcl:1237 -edge_shift length does not match -edges length.
|
|
537 Sdc.tcl:1243 missing -multiply_by, -divide_by, -combinational or -edges argument.
|
|
538 Sdc.tcl:1251 cannot specify -invert without -multiply_by, -divide_by or -combinational.
|
|
539 Sdc.tcl:1257 -duty_cycle requires -multiply_by value.
|
|
540 Sdc.tcl:1262 missing -pll_output argument.
|
|
541 Sdc.tcl:1265 missing -pll_feedback argument.
|
|
542 Sdc.tcl:1271 PLL output and feedback pins must be on the same instance.
|
|
543 Sdc.tcl:1274 source pin must be on the same instance as the PLL output pin.
|
|
544 Sdc.tcl:1277 PLL output must be one of the clock pins.
|
|
545 Sdc.tcl:1315 group_path command failed.
|
|
546 Sdc.tcl:1322 positional arguments not supported.
|
|
547 Sdc.tcl:1326 -from, -through or -to required.
|
|
548 Sdc.tcl:1332 -name and -default are mutually exclusive.
|
|
549 Sdc.tcl:1334 -name or -default option is required.
|
|
550 Sdc.tcl:1375 cannot specify both -high and -low.
|
|
551 Sdc.tcl:1383 missing -setup or -hold argument.
|
|
552 Sdc.tcl:1397 -high and -low only permitted for pins and instances.
|
|
553 Sdc.tcl:1404 -high and -low only permitted for pins and instances.
|
|
554 Sdc.tcl:1447 one of -logically_exclusive, -physically_exclusive or -asynchronous is required.
|
|
555 Sdc.tcl:1450 the keywords -logically_exclusive, -physically_exclusive and -asynchronous are mutually exclusive.
|
|
556 Sdc.tcl:1518 -source '[get_full_name $pin]' is not a clock pin.
|
|
557 Sdc.tcl:1525 -early/-late is only allowed with -source.
|
|
558 Sdc.tcl:1554 set_sense -type clock|data
|
|
559 Sdc.tcl:1623 transition time can not be specified for virtual clocks.
|
|
560 Sdc.tcl:1644 missing uncertainty value.
|
|
561 Sdc.tcl:1686 -from/-to must be used together.
|
|
562 Sdc.tcl:1706 -rise, -fall options not allowed for single clock uncertainty.
|
|
563 Sdc.tcl:1747 missing -from, -rise_from or -fall_from argument.
|
|
564 Sdc.tcl:1759 missing -to, -rise_to or -fall_to argument.
|
|
565 Sdc.tcl:1831 -from/-to hierarchical instance not supported.
|
|
566 Sdc.tcl:1863 pin '[get_full_name $inst]${hierarchy_separator}${port_name}' not found.
|
|
567 Sdc.tcl:1904 pin '[get_name $cell]${hierarchy_separator}${port_name}' not found.
|
|
568 Sdc.tcl:2089 missing delay argument.
|
|
569 Sdc.tcl:2220 missing path multiplier argument.
|
|
570 Sdc.tcl:2232 cannot use -start with -end.
|
|
571 Sdc.tcl:2300 value must be 0, zero, 1, one, rise, rising, fall, or falling.
|
|
572 Sdc.tcl:2358 cell '$lib_name:$cell_name' not found.
|
|
573 Sdc.tcl:2364 '$cell_name' not found.
|
|
574 Sdc.tcl:2368 missing -lib_cell argument.
|
|
575 Sdc.tcl:2376 port '$to_port_name' not found.
|
|
576 Sdc.tcl:2388 -pin argument required for cells with multiple outputs.
|
|
577 Sdc.tcl:2403 port '$from_port_name' not found.
|
|
578 Sdc.tcl:2610 port '[get_name $port]' is not an input.
|
|
579 Sdc.tcl:2972 operating condition '$op_cond_name' not found.
|
|
580 Sdc.tcl:2990 operating condition '$op_cond_name' not found.
|
|
581 Sdc.tcl:3004 -analysis_type must be single, bc_wc or on_chip_variation.
|
|
582 Sdc.tcl:3029 mode must be top, enclosed or segmented.
|
|
583 Sdc.tcl:3044 no wire load model specified.
|
|
584 Sdc.tcl:3105 wire load selection group '$selection_name' not found.
|
|
585 Sdc.tcl:3233 no default operating conditions found.
|
|
586 NetworkEdit.tcl:50 unsupported object type $object_type.
|
|
587 NetworkEdit.tcl:119 unsupported object type $object_type.
|
|
588 NetworkEdit.tcl:135 unsupported object type $object_type.
|
|
589 Network.tcl:25 unknown namespace $namespc.
|
|
590 Network.tcl:55 instance $instance_path not found.
|
|
591 Network.tcl:274 net $net_path not found.
|
|
592 Network.tcl:277 net $net_path not found.
|
|
593 Link.tcl:28 missing top_cell_name argument and no current_design.
|
|
594 DelayNormal1.cc:203 unknown early/late value.
|
|
595 DelayNormal2.cc:378 unknown early/late value.
|
|
596 Sim.cc:199 unknown function operator
|
|
597 EstimateParasitics.cc:188 load pin not leaf or top level
|
|
600 Sdc.tcl:1945 '$args' ignored.
|
|
601 Sdc.tcl:2444 set_fanout_load not supported.
|
|
602 Sdc.tcl:2904 no valid objects specified for $key.
|
|
603 NetworkEdit.tcl:172 disconnect_pins is deprecated. Use disconnect_pin.
|
|
604 Sdc.tcl:270 unknown $unit prefix '$prefix'.
|
|
605 Sdc.tcl:3066 wire load model '$model_name' not found.
|
|
606 Cmds.tcl:1875 get_property unsupported object type $object_type.
|
|
607 StaTcl.i unknown report path field %s
|
|
608 StaTcl.i unknown report path field %s
|
|
|