98 lines
3.0 KiB
Systemverilog
98 lines
3.0 KiB
Systemverilog
// DESCRIPTION: Verilator: Verilog Test module
|
|
//
|
|
// This file ONLY is placed under the Creative Commons Public Domain, for
|
|
// any use, without warranty, 2008 by Wilson Snyder.
|
|
// SPDX-License-Identifier: CC0-1.0
|
|
|
|
module t ( /*AUTOARG*/
|
|
// Inputs
|
|
clk
|
|
);
|
|
input clk;
|
|
|
|
integer cyc = 0;
|
|
reg [63:0] crc;
|
|
|
|
reg negate;
|
|
reg enable;
|
|
|
|
wire [31:0] datA = crc[31:0];
|
|
wire [31:0] datB = crc[63:32];
|
|
|
|
// Predict result
|
|
wire [63:0] muled = (negate ? (-{32'h0, datA} * {32'h0, datB}) : ({32'h0, datA} * {32'h0, datB}));
|
|
reg [63:0] muled_d1;
|
|
reg [63:0] muled_d2;
|
|
reg [63:0] muled_d3;
|
|
reg [63:0] muled_d4;
|
|
reg enable_d1;
|
|
reg enable_d2;
|
|
reg enable_d3;
|
|
always @(posedge clk) enable_d1 <= enable;
|
|
always @(posedge clk) enable_d2 <= enable_d1;
|
|
always @(posedge clk) enable_d3 <= enable_d2;
|
|
always @(posedge clk) if (enable) muled_d1 <= muled;
|
|
always @(posedge clk) if (enable_d1) muled_d2 <= muled_d1;
|
|
always @(posedge clk) if (enable_d2) muled_d3 <= muled_d2;
|
|
always @(posedge clk) if (enable_d3) muled_d4 <= muled_d3;
|
|
|
|
/*AUTOWIRE*/
|
|
// Beginning of automatic wires (for undeclared instantiated-module outputs)
|
|
wire [64:0] product_d4; // From test of t_math_synmul_mul.v
|
|
// End of automatics
|
|
|
|
t_math_synmul_mul test ( /*AUTOINST*/
|
|
// Outputs
|
|
.product_d4 (product_d4[64:0]),
|
|
// Inputs
|
|
.clk (clk),
|
|
.enable (enable),
|
|
.negate (negate),
|
|
.datA (datA[31:0]),
|
|
.datB (datB[31:0]));
|
|
|
|
integer cycs_enabled;
|
|
initial cycs_enabled = 0;
|
|
|
|
// Test loop
|
|
always @(posedge clk) begin
|
|
`ifdef TEST_VERBOSE
|
|
$write("[%0t] cyc==%0d crc=%x e=%x n=%x a*b=%x synmul=%x\n", $time, cyc, crc, enable, negate,
|
|
muled_d4, product_d4[63:0]);
|
|
`endif
|
|
cyc <= cyc + 1;
|
|
crc <= {crc[62:0], crc[63] ^ crc[2] ^ crc[0]};
|
|
negate <= 1'b0; // Negation not currently supported
|
|
|
|
// Always enable in low cycle counts to clear out the pipe
|
|
//enable <= 1'b1; // 100% activity factor
|
|
enable <= (cyc < 10 || cyc[4]); // 50% activity factor
|
|
//enable <= (cyc<10 || cyc[4]&cyc[3]); // 25% activity factor
|
|
|
|
if (enable) cycs_enabled = cycs_enabled + 1;
|
|
if (cyc == 0) begin
|
|
// Setup
|
|
crc <= 64'h5aef0c8d_d70a4497;
|
|
end
|
|
else begin
|
|
if (product_d4[63:0] !== muled_d4) begin
|
|
$write("[%0t] BAD product, got=%x exp=%x at cyc 0x%x\n", $time, product_d4[63:0], muled_d4,
|
|
cyc);
|
|
$stop;
|
|
end
|
|
if (cyc == 99) begin
|
|
if (crc !== 64'hc77bb9b3784ea091) $stop;
|
|
end
|
|
`ifndef SIM_CYCLES
|
|
`define SIM_CYCLES 99
|
|
`endif
|
|
if (cyc == `SIM_CYCLES) begin
|
|
$write("- Cycles=%0d, Activity factor=%0d%%\n", cyc, ((cycs_enabled * 100) / cyc));
|
|
$write("*-* All Finished *-*\n");
|
|
$finish;
|
|
end
|
|
end
|
|
end
|
|
|
|
endmodule
|