53 lines
3.0 KiB
Plaintext
53 lines
3.0 KiB
Plaintext
|
.. _troubleshooting:
|
||
|
|
|
||
|
|
Troubleshooting
|
||
|
|
###############
|
||
|
|
|
||
|
|
I installed openFPGALoader but it says `command not found` when I try to launch it
|
||
|
|
==================================================================================
|
||
|
|
|
||
|
|
The correct spelling of the program is *openFPGALoader* with FPGA and the "L" of "Loader" in uppercase.
|
||
|
|
Ensure the spelling of the program is correct.
|
||
|
|
|
||
|
|
Gowin device could not communicate since last bitstream flashed. (issue `#206 <https://github.com/trabucayre/openFPGALoader/issues/206>`_)
|
||
|
|
==========================================================================================================================================
|
||
|
|
|
||
|
|
Gowin's FPGA may fails to be detected if **JTAGSEL_N** (pin 08 for *GW1N-4K*) is used as a GPIO.
|
||
|
|
To recover you have to pull down this pin (before power up) to recover JTAG interface (*UG292 - JTAGSELL_N section*).
|
||
|
|
|
||
|
|
JTAG init failed
|
||
|
|
================
|
||
|
|
|
||
|
|
Avoid using USB hubs and connect it directly to your PC USB port.
|
||
|
|
|
||
|
|
|
||
|
|
Tang Primer 20k program slow and stucked (issue `#250 <https://github.com/trabucayre/openFPGALoader/issues/250>`_)
|
||
|
|
==================================================================================================================
|
||
|
|
|
||
|
|
Check your openFPGALoader version:
|
||
|
|
|
||
|
|
.. code:: bash
|
||
|
|
|
||
|
|
openFPGALoader -V
|
||
|
|
|
||
|
|
If it is older than release then v0.9.0, install the most recent version (from commit `f5b89bff68a5e2147404a895c075773884077438 <https://github.com/trabucayre/openFPGALoader/commit/fe259fb78d185b3113661d04cd7efa9ae0232425>`_ or later).
|
||
|
|
|
||
|
|
Cannot flash Tang Nano 20k (issue `#251 <https://github.com/trabucayre/openFPGALoader/issues/511>`_)
|
||
|
|
====================================================================================================
|
||
|
|
|
||
|
|
Some firmware version cannot be flashed on Linux-based systems. Version 2024122312 is such an example. It seems this version was not published on the `SiPeed website <https://api.dl.sipeed.com/TANG/Debugger/onboard/BL616/>`_, however some boards sold have this firmware.
|
||
|
|
|
||
|
|
The cause of the problem is the debugger on the Tang Nano, specifically the firmware of this debugger. This firmware can be easily updated by following `these <https://wiki.sipeed.com/hardware/en/tang/common-doc/update_debugger.html>`_ steps.
|
||
|
|
|
||
|
|
Cannot flash Tang Nano 9k (issue `#251 <https://github.com/trabucayre/openFPGALoader/issues/251>`_)
|
||
|
|
===================================================================================================
|
||
|
|
|
||
|
|
This is a device issue, erase its Embedded Flash using Official GoWin Programmer (preferentially in Windows) and SRAM too, then you can use openFPGALoader again.
|
||
|
|
|
||
|
|
Unable to open FTDI device: -4 (usb_open() failed) (issue `#245 <https://github.com/trabucayre/openFPGALoader/issues/245>`_)
|
||
|
|
============================================================================================================================
|
||
|
|
|
||
|
|
Edit your `/etc/udev/rules.d/99-ftdi.rules` file exchanging your programming device permissions.
|
||
|
|
|
||
|
|
For more information, check the udev section from `this guide <install.rst>`_
|