magic/doc/latexfiles/Makefile.in

76 lines
2.9 KiB
Makefile

# Provided by configure: the module's source dir + the build top.
# defs.mak sees `srcdir` already set and skips its own srcdir derivation.
srcdir = @srcdir@
VPATH = @srcdir@
MAGICDIR = @top_builddir@
include $(MAGICDIR)/defs.mak
# PS_SRCDIR: pre-built PostScript shipped in the source tree (read-only, used by
# install when a doc has not been regenerated).
# PS_GENDIR: regenerated PostScript, written into the build tree (never source).
PS_SRCDIR=${MAGICSRC}/doc/psfiles
PS_GENDIR=psfiles
PS_INSTDIR=$(INSTALL_LIBDIR)/magic/doc
.SUFFIXES: .dvi .tex .ps
GENDVI=tut1.dvi tut2.dvi tut3.dvi tut4.dvi tut5.dvi tut6.dvi \
tut7.dvi tut8.dvi tut9.dvi tut10.dvi tut11.dvi \
maint1.dvi maint2.dvi maint3.dvi maint4.dvi \
introduction.dvi copyright.dvi addendum6_5.dvi \
tutscm1.dvi tutscm2.dvi tutscm3.dvi tutscm4.dvi \
tuttcl1.dvi tuttcl2.dvi tuttcl3.dvi tuttcl4.dvi tuttcl5.dvi \
tutwrl1.dvi
GENPS=tut1.ps tut2.ps tut3.ps tut4.ps tut5.ps tut6.ps \
tut7.ps tut8.ps tut9.ps tut10.ps tut11.ps \
maint1.ps maint2.ps maint3.ps maint4.ps \
introduction.ps copyright.ps addendum6_5.ps \
tutscm1.ps tutscm2.ps tutscm3.ps tutscm4.ps \
tuttcl1.ps tuttcl2.ps tuttcl3.ps tuttcl4.ps tuttcl5.ps \
tutwrl1.ps
GEN_GENPS= $(GENPS:%=${PS_GENDIR}/%)
INST_GENPS= $(GENPS:%=$(DESTDIR)${PS_INSTDIR}/%)
# Regenerate all PostScript into the build tree (${PS_GENDIR}).
all: $(GEN_GENPS)
@${RM} $(GENDVI) *.log *.aux
install: $(DESTDIR)${PS_INSTDIR} ${INST_GENPS}
$(DESTDIR)${PS_INSTDIR}: make-doc-dir
make-doc-dir:
${SCRIPTS}/mkdirs $(DESTDIR)${PS_INSTDIR}
# Install each PostScript file from the build tree if it was regenerated there,
# otherwise from the pre-built copy shipped in the source tree.
$(DESTDIR)${PS_INSTDIR}/%: $(DESTDIR)${PS_INSTDIR}
@f=${PS_GENDIR}/$*; test -f $$f || f=${PS_SRCDIR}/$*; \
echo "${CP} $$f $(DESTDIR)${PS_INSTDIR}/$*"; \
${CP} $$f $(DESTDIR)${PS_INSTDIR}/$*
# Regenerate a .ps (into the build tree) from its .tex (in the source tree).
# Several .tex include figures as ../psfigures/*.ps (relative to this dir).
# Out-of-tree that would resolve into the empty build tree, so point the
# build-tree ../psfigures at the source copy (a no-op in-tree, where it already
# exists); both latex and dvips then find the figures, outputs stay in-build.
${PS_GENDIR}/%.ps: %.tex
@mkdir -p ${PS_GENDIR}
@test -e ../psfigures || ln -s ${MAGICSRC}/doc/psfigures ../psfigures
@echo "Converting $*.tex -> $*.dvi"
@TEXINPUTS=$(srcdir): ${LATEX} $(srcdir)/$*.tex < /dev/null > /dev/null
@if grep 'LaTeX Warn' $*.log; \
then \
echo "Detected warnings, doing second pass for $*...";\
TEXINPUTS=$(srcdir): ${LATEX} $(srcdir)/$*.tex < /dev/null > /dev/null; \
(grep 'LaTeX Warn' $*.log || (echo > /dev/null)); \
echo; \
fi
@echo "Converting $*.dvi -> ${PS_GENDIR}/$*.ps"
@${DVIPS} -t letter $*.dvi -o ${PS_GENDIR}/$*.ps > /dev/null
clean:
${RM} $(GENDVI) $(GEN_GENPS) *.log *.aux