on a non-writeable cell. While technically valid, that just means
that nobody can make temporary edits on the cell in memory, which is
useful in many applications. A slight quirk of the "cellname" command
is that if applied to the cell currently in the layout window, it is
not possible to make the cell show as edited and editable until leaving
and re-entering the cell.
that the intersection of (A and-not B) can be found. This and the
(A and B) version give a large amount of capability like the cifoutput
operators available as command-line commands. Also: Fixed the new
"drop" command so that it properly redisplays and runs DRC after
executing, and modified the behavior so that the dropped material
is clipped to the area of the selection.
into subcells in a hierarchy. The intent is to use this in
conjunction with the "select intersect" command option added
yesterday to add deep nwell into the cells containing the devices
that need it.
GDS_FILE property in the same way that it handles changes to the
FIXED_BBOX property, by setting or clearing the associated flag
bit in the cell. Otherwise, it becomes impossible to make a
cell writeable, as it always has some belief that it is still
attached to a specific GDS file. Corrected an error in the
"gds" ("calma") command parsing that switched the callbacks for
the "noduplicates" and "nodatestamp" options.
it as a single value "flags" (unsigned char) with meaningful flag
names. Added new option "-fail" to the load command to allow
magic to fail on loading a cell that does not have a corresponding
file rather than the default action of creating a new cell. Added
a flag for the "-quiet" option so that behavior on "-fail" can be
done quietly.
to stop the search whenever a cell is not found. Used this to implement
a new option for GDS writes, "gds undefined allow|disallow" (default
"disallow") controls whether or not GDS with undefined references will
be allowed to be written. Similarly affects CIF and LEF writes, extraction,
and DRC (when running "drc check" from the top).
of input cells on a per-cellname basis, using glob-style pattern
matching. This is probably the best way to deal with 3rd-party vendor
GDS with unfortunate practices like dividing devices up among cells in
a hierarchy, even though it comes across as a bit of a hack solution.
true, this will force the "gds write" command to write out creation
date stamps as zero. This is very useful for avoiding changing the
contents of an otherwise-unchanged layout, especially if it is in
a git repository where it will force the entire file to be replaced.
to allow a cell to be flushed with dereferencing (i.e., discard any file
path attached to the cell, and use the search paths to find the cell when
it is reloaded).
to allow a "gds read" command to ignore cells in the GDS which already
exist in memory. This allows magic to be "pre-seeded" with specific
views of cells in the GDS. Default is false, which is backwards-
compatble behavior. (2) Changed the behavior of the the way the use
path is written to and read from a .mag file, checking the path prefix
against Tcl variables PDK_PATH, PDKPATH, PDK_ROOT, and PDKROOT, and
replacing any such leading path component with the variable name.
On reading a .mag file, any variable name at the start of the path
that matches a Tcl variable will be substituted.
used both for counting cells during GDS write and for saving
geometry data from the "copyup" operator during GDS read. The write
routine does not clear the client record, and the read routine was
checking if the cd_client value was default. Corrected the resulting
crash condition by resetting cd_client before GDS reads. However, the
underlying problem is that the GDS read is reading data into a cell
that already exists in the database, and is not handling it robustly
by renaming the existing cell. So this should be revisited.
Instead of a 6-character suffix generated randomly, the 6-character
suffix is generated by a hash algorithm from the device parameters.
If the cell parameters are changed, then the cell itself changes.
If the instance name was default (derived from the cell name) then
the instance name changes accordingly. The result is that there
cannot be two (auto-)generated cells with the same parameters but
with different cell names.
optional name field to the "substrate" line in the extract section
of the techfile. This is the default name of the substrate if not
connected to anything labeled. It may use a Tcl variable (preferred).
(2) Added command option "instance orientation [-def]" that returns
the orientation of the named or selected instance. The -def option
returns the orientation using DEF naming convention; otherwise, the
naming used with "getcell" is generated.
argument as a pointer but also set the same variable to the
return value. This is ambiguous, because the behavior depends on
whether the value being set upon return is the original value or
the reallocated value. The result is system-dependent behavior.
Conflicts:
VERSION
Merged recent changes from master back into bplane, as the efficiency of
bplane for doing extraction on large layouts is unquestionably better.
Fixed the implementation of DBMoveCell() for bplane. Corrected an error
in the bplane version of dbScaleCell() that enumerates cell uses but
does not free the list.
coordinate system origin to the specified (current) location.
This is a much more efficient method than selecting everything in
a layout and moving it, especially for very large layouts where
selection and moving becomes prohibitive.
Conflicts:
VERSION
database/DBcellsrch.c
database/DBconnect.c
extract/ExtInter.c
lef/Depend
utils/Depend
Updated bplane branch with all changes to master since the bplane branch
was last modified.
which had been changed a few months back to remove the individual
cell count and only list the top level cell. The behavior has been
changed a bit so that "list" returns values for the top level cell
only, but "listall" returns a complete list. "drc list count total"
gives the DRC count for the top cell, but "drc listall count total"
gives the DRC count for everything (probably not very useful).
Also: Implemented a behavior by request to automatically removed
the (UNNAMED) cell whenever a new cell is loaded and the (UNNAMED)
cell has not been modified.
to be investigated here. I am no longer sure why I removed the
cell search from DRC count, but it appears that the cell search is
non-functional, and it should be determined why. There is no
particular reason not to have a DRC count search. It could be
implemented such that "list" vs. "listall" counts the top cell vs.
all cells. First it must be determined why there are no subcell
counts.
only at the time of running the command "load". But cells are generally
loaded only on an as-needed basis, so the dereferencing option must be
saved as a flag in the cell and honored whenever its subcells are expanded
or otherwise read at a later time.
categorized by error type and scrolled through conveniently. However,
it needs work dealing with finding the actual error bounds. The
"DRC count" counts tiles, which is tile-plane-geometry-specific, and
"DRC listall why" fractures errors both over tiles and over the square
areas that the interactive DRC splits the layout into, for performance.
The DRC error plane needs to be changed to hold different types for
each error class, so that errors can be scanned by boundary instead of
by tile (work to be done).
rid of redundant port entries in subcircuits. There is still an outstanding
issue as to whether nodes and connections need to be recursively iterated
to the hierarchy bottom. The current fix corrected the test case. Also,
added a "-dereference" option to the "load" command to revert to the
original behavior of using only search paths from "addpath" when searching
for files to load.
(once corrected in an experimental branch but never merged). This
avoids changing the actual bounding box of the cell to match the
LEF bounding box, but defines a property instead and uses that
property for certain functions such as displaying the bounding box
outline or selecting the cell. This avoids certain related errors
such as the failure to extract connections to areas outside of the
fixed bounding box.
routine was erasing and redrawing in one step, which ignored the
possibility of having to erase from one window and redraw in
another if the cursor moved focus from one window to another.
This led to crosshairs being improperly drawn and erased when
multiple windows were present, if the windows had different cells
loaded.
This correction allows a full path to be passed for the cellname
and will (correctly) break the path into cell name and path
components (previously was naming the cell with the full path).
To avoid name conflicts, the cell name gets modified if the path
cannot be resolved against an existing cell of the same name.
that are longer than the formerly-fixed array size 256. This
conflicted with the recent addition of holding path data in
properties, where the path coordinates can be significantly
longer than the fixed array size. Same change as made to magic
version 8.1.
from "gds polygon subcell". Previously both polygons and paths
were put into subcells named polygonXXXXX (substitute numbers
for XXXXX). Now polygons go into cells named polygonXXXXX and
paths go into cells named pathXXXXX. This makes it easier to
keep track of the original path. NOTE: The path centerline
should be kept as a cell property in this case, and the path
options like endcap style can also be held as properties. The
polygon boundary should be treated similarly.
Tim Edwards