luke
/
UberDDR3
mirror of https://github.com/AngeloJacobo/UberDDR3.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
UberDDR3/example_demo/arty_s7/arty_ddr3.v

205 lines
8.8 KiB
Verilog
Raw Blame History

////////////////////////////////////////////////////////////////////////////////
//
// Filename: arty_ddr3.v
// Project: UberDDR3 - An Open Source DDR3 Controller
//
// Purpose: Example demo of UberDDR3 for Arty-S7. Mechanism:
// - four LEDs will light up once UberDDR3 is done calibrating
// - if UART (9600 Baud Rate)receives small letter ASCII (a-z), this value will be written to DDR3
// - if UART receives capital letter ASCII (A-Z), the small letter equivalent will be retrieved from DDR3 by doing
// - a read request, once read data is available this will be sent to UART to be streamed out.
// THUS:
// - Sendng "abcdefg" to the UART terminal will store that small latter to DDR3
// - Then sending "ABCDEFG" to the UART terminal will return the small letter equivalent: "abcdefg"
//
// Engineer: Angelo C. Jacobo
//
////////////////////////////////////////////////////////////////////////////////
//
// Copyright (C) 2023-2024 Angelo Jacobo
//
// This program is free software: you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation, either version 3 of the License, or
// (at your option) any later version.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program. If not, see <https://www.gnu.org/licenses/>.
//
////////////////////////////////////////////////////////////////////////////////
`timescale 1ns / 1ps
module arty_ddr3
(
input wire i_clk,
input wire i_rst,
// DDR3 I/O Interface
output wire ddr3_clk_p, ddr3_clk_n,
output wire ddr3_reset_n,
output wire ddr3_cke, // CKE
output wire ddr3_cs_n, // chip select signal
output wire ddr3_ras_n, // RAS#
output wire ddr3_cas_n, // CAS#
output wire ddr3_we_n, // WE#
output wire[14-1:0] ddr3_addr,
output wire[3-1:0] ddr3_ba,
inout wire[16-1:0] ddr3_dq,
inout wire[2-1:0] ddr3_dqs_p, ddr3_dqs_n,
output wire[2-1:0] ddr3_dm,
output wire ddr3_odt, // on-die termination
// UART line
input wire rx,
output wire tx,
//Debug LEDs
output wire[3:0] led
);
wire i_controller_clk, i_ddr3_clk, i_ref_clk, i_ddr3_clk_90;
wire m_axis_tvalid;
wire rx_empty;
wire tx_full;
wire o_wb_ack;
wire[7:0] o_wb_data;
wire o_aux;
wire[7:0] rd_data;
wire o_wb_stall;
reg i_wb_stb = 0, i_wb_we;
wire[63:0] o_debug1;
reg[7:0] i_wb_data;
reg[7:0] i_wb_addr;
// o_debug1 taps on value of state_calibrate (can be traced inside ddr3_controller module)
assign led[0] = (o_debug1[4:0] == 23); //light up if at DONE_CALIBRATE
assign led[1] = (o_debug1[4:0] == 23); //light up if at DONE_CALIBRATE
assign led[2] = (o_debug1[4:0] == 23); //light up if at DONE_CALIBRATE
assign led[3] = (o_debug1[4:0] == 23); //light up if at DONE_CALIBRATE
always @(posedge i_controller_clk) begin
begin
i_wb_stb <= 0;
i_wb_we <= 0;
i_wb_addr <= 0;
i_wb_data <= 0;
if(!o_wb_stall && m_axis_tvalid) begin
if(rd_data >= 97 && rd_data <= 122) begin //write to DDR3 if ASCII is small letter
i_wb_stb <= 1;
i_wb_we <= 1;
i_wb_addr <= ~rd_data ;
i_wb_data <= rd_data;
end
else if(rd_data >= 65 && rd_data <= 90) begin //read from DDR3 if ASCII is capital letter
i_wb_stb <= 1; //make request
i_wb_we <= 0; //read
i_wb_addr <= ~(rd_data + 8'd32);
end
end
end
end
(* mark_debug = "true" *) wire clk_locked;
clk_wiz clk_wiz_inst
(
// Clock out ports
.clk_out1(i_controller_clk), //83.333 Mhz
.clk_out2(i_ddr3_clk), // 333.333 MHz
.clk_out3(i_ref_clk), //200MHz
.clk_out4(i_ddr3_clk_90), // 333.333 MHz with 90degree shift
// Status and control signals
.reset(i_rst),
.locked(clk_locked),
// Clock in ports
.clk_in1(i_clk)
);
// UART module from https://github.com/alexforencich/verilog-uart
uart #(.DATA_WIDTH(8)) uart_m
(
.clk(i_controller_clk),
.rst(i_rst),
.s_axis_tdata(o_wb_data),
.s_axis_tvalid(o_wb_ack),
.s_axis_tready(),
.m_axis_tdata(rd_data),
.m_axis_tvalid(m_axis_tvalid),
.m_axis_tready(1),
.rxd(rx),
.txd(tx),
.prescale(1085) //9600 Baud Rate (83.33MHz/(8*9600))
);
// DDR3 Controller
ddr3_top #(
.CONTROLLER_CLK_PERIOD(12_000), //ps, clock period of the controller interface
.DDR3_CLK_PERIOD(3_000), //ps, clock period of the DDR3 RAM device (must be 1/4 of the CONTROLLER_CLK_PERIOD)
.ROW_BITS(14), //width of row address
.COL_BITS(10), //width of column address
.BA_BITS(3), //width of bank address
.BYTE_LANES(2), //number of DDR3 modules to be controlled
.AUX_WIDTH(4), //width of aux line (must be >= 4)
.WB2_ADDR_BITS(32), //width of 2nd wishbone address bus
.WB2_DATA_BITS(32), //width of 2nd wishbone data bus
.MICRON_SIM(0), //enable faster simulation for micron ddr3 model (shorten POWER_ON_RESET_HIGH and INITIAL_CKE_LOW)
.ODELAY_SUPPORTED(0), //set to 1 when ODELAYE2 is supported
.SECOND_WISHBONE(0) //set to 1 if 2nd wishbone is needed
) ddr3_top
(
//clock and reset
.i_controller_clk(i_controller_clk),
.i_ddr3_clk(i_ddr3_clk), //i_controller_clk has period of CONTROLLER_CLK_PERIOD, i_ddr3_clk has period of DDR3_CLK_PERIOD
.i_ref_clk(i_ref_clk),
.i_ddr3_clk_90(i_ddr3_clk_90),
.i_rst_n(!i_rst && clk_locked),
// Wishbone inputs
.i_wb_cyc(1), //bus cycle active (1 = normal operation, 0 = all ongoing transaction are to be cancelled)
.i_wb_stb(i_wb_stb), //request a transfer
.i_wb_we(i_wb_we), //write-enable (1 = write, 0 = read)
.i_wb_addr(i_wb_addr), //burst-addressable {row,bank,col}
.i_wb_data(i_wb_data), //write data, for a 4:1 controller data width is 8 times the number of pins on the device
.i_wb_sel(16'hffff), //byte strobe for write (1 = write the byte)
.i_aux(i_wb_we), //for AXI-interface compatibility (given upon strobe)
// Wishbone outputs
.o_wb_stall(o_wb_stall), //1 = busy, cannot accept requests
.o_wb_ack(o_wb_ack), //1 = read/write request has completed
.o_wb_data(o_wb_data), //read data, for a 4:1 controller data width is 8 times the number of pins on the device
.o_aux(o_aux),
// Wishbone 2 (PHY) inputs
.i_wb2_cyc(), //bus cycle active (1 = normal operation, 0 = all ongoing transaction are to be cancelled)
.i_wb2_stb(), //request a transfer
.i_wb2_we(), //write-enable (1 = write, 0 = read)
.i_wb2_addr(), //burst-addressable {row,bank,col}
.i_wb2_data(), //write data, for a 4:1 controller data width is 8 times the number of pins on the device
.i_wb2_sel(), //byte strobe for write (1 = write the byte)
// Wishbone 2 (Controller) outputs
.o_wb2_stall(), //1 = busy, cannot accept requests
.o_wb2_ack(), //1 = read/write request has completed
.o_wb2_data(), //read data, for a 4:1 controller data width is 8 times the number of pins on the device
// PHY Interface (to be added later)
// DDR3 I/O Interface
.o_ddr3_clk_p(ddr3_clk_p),
.o_ddr3_clk_n(ddr3_clk_n),
.o_ddr3_reset_n(ddr3_reset_n),
.o_ddr3_cke(ddr3_cke), // CKE
.o_ddr3_cs_n(ddr3_cs_n), // chip select signal (controls rank 1 only)
.o_ddr3_ras_n(ddr3_ras_n), // RAS#
.o_ddr3_cas_n(ddr3_cas_n), // CAS#
.o_ddr3_we_n(ddr3_we_n), // WE#
.o_ddr3_addr(ddr3_addr),
.o_ddr3_ba_addr(ddr3_ba),
.io_ddr3_dq(ddr3_dq),
.io_ddr3_dqs(ddr3_dqs_p),
.io_ddr3_dqs_n(ddr3_dqs_n),
.o_ddr3_dm(ddr3_dm),
.o_ddr3_odt(ddr3_odt), // on-die termination
.o_debug1(o_debug1),
.o_debug2(),
.o_debug3()
);
endmodule
Reference in New Issue View Git Blame Copy Permalink