added testbench for a single ddr3 device sim

2023-06-03 14:28:55 +08:00 · 2023-06-03 14:28:55 +08:00 · 98ed92a65b
parent 9a19f82377
commit 98ed92a65b
1 changed files with 210 additions and 0 deletions
--- a/Model/ddr3_micron_sim.v
+++ b/Model/ddr3_micron_sim.v
@ -0,0 +1,210 @@
+
+//////////////////////////////////////////////////////////////////////////////////
+// Company: 
+// Engineer: 
+// 
+// Create Date: 05/13/2023 07:48:19 AM
+// Design Name: 
+// Module Name: ddr3_micron_sim
+// Project Name: 
+// Target Devices: 
+// Tool Versions: 
+// Description: 
+// 
+// Dependencies: 
+// 
+// Revision:
+// Revision 0.01 - File Created
+// Additional Comments:
+// 
+//////////////////////////////////////////////////////////////////////////////////
+
+`timescale 1ps / 1ps
+`define den8192Mb
+`define sg125
+`define x8
+
+module ddr3_micron_sim;
+`ifdef den1024Mb
+    `include "1024Mb_ddr3_parameters.vh"
+`elsif den2048Mb
+    `include "2048Mb_ddr3_parameters.vh"
+`elsif den4096Mb
+    `include "4096Mb_ddr3_parameters.vh"
+`elsif den8192Mb
+    `include "8192Mb_ddr3_parameters.vh"
+`else
+    // NOTE: Intentionally cause a compile fail here to force the users
+    //       to select the correct component density before continuing
+    ERROR: You must specify component density with +define+den____Mb.
+`endif
+
+
+ reg i_controller_clk, i_ddr3_clk;
+ reg i_rst_n;
+ // Wishbone Interface
+ reg i_wb_cyc; //bus cycle active (1 = normal operation, 0 = all ongoing transaction are to be cancelled)
+ reg i_wb_stb; //request a transfer
+ reg i_wb_we; //write-enable (1 = write, 0 = read)
+ reg[$bits(ddr3_controller.i_wb_addr)-1:0] i_wb_addr; //burst-addressable {row,bank,col} 
+ reg[$bits(ddr3_controller.i_wb_data)-1:0] i_wb_data; //write data, for a 4:1 controller data width is 8 times the number of pins on the device
+ wire o_wb_stall; //1 = busy, cannot accept requests
+ wire o_wb_ack; //1 = read/write request has completed
+ wire[$bits(ddr3_controller.o_wb_data)-1:0] o_wb_data; //read data, for a 4:1 controller data width is 8 times the number of pins on the device
+ // PHY Interface to DDR3 Device
+  wire ck_en; // CKE
+  wire cs_n; // chip select signal
+  wire odt; // on-die termination
+  wire ras_n; // RAS#
+  wire cas_n; // CAS#
+  wire we_n; // WE#
+  wire reset_n;
+  wire[$bits(ddr3_top.o_ddr3_addr)-1:0] addr;
+  wire[$bits(ddr3_top.o_ddr3_ba_addr)-1:0] ba_addr;
+  wire[$bits(ddr3_top.io_ddr3_dq)-1:0] dq;
+  wire[$bits(ddr3_top.io_ddr3_dqs)-1:0] dqs;
+  wire[$bits(ddr3_top.io_ddr3_dqs_n)-1:0] dqs_n;
+  wire o_ddr3_clk_p, o_ddr3_clk_n;
+ 
+ 
+// DDR3 Controller 
+ddr3_top #(
+    .ROW_BITS(14),   //width of row address
+    .COL_BITS(10), //width of column address
+    .BA_BITS(3), //width of bank address
+    .DQ_BITS(8),  //width of DQ
+    .CONTROLLER_CLK_PERIOD(5), //ns, period of clock input to this DDR3 controller module
+    .DDR3_CLK_PERIOD(1.25), //ns, period of clock input to DDR3 RAM device 
+    .LANES(1), //8 lanes of DQ
+    .OPT_LOWPOWER(1), //1 = low power, 0 = low logic
+    .OPT_BUS_ABORT(1)  //1 = can abort bus, 0 = no absort (i_wb_cyc will be ignored, ideal for an AXI implementation which cannot abort transaction)
+    ) ddr3_top
+    (
+        .i_controller_clk(i_controller_clk),
+        .i_ddr3_clk(i_ddr3_clk), //i_controller_clk has period of CONTROLLER_CLK_PERIOD, i_ddr3_clk has period of DDR3_CLK_PERIOD 
+        .i_ref_clk(i_controller_clk),
+        .i_rst_n(i_rst_n), //200MHz input clock
+        // Wishbone inputs
+        .i_wb_cyc(i_wb_cyc), //bus cycle active (1 = normal operation, 0 = all ongoing transaction are to be cancelled)
+        .i_wb_stb(i_wb_stb), //request a transfer
+        .i_wb_we(i_wb_we), //write-enable (1 = write, 0 = read)
+        .i_wb_addr(i_wb_addr), //burst-addressable {row,bank,col} 
+        .i_wb_data(i_wb_data), //write data, for a 4:1 controller data width is 8 times the number of pins on the device
+        .i_wb_sel(), //byte strobe for write (1 = write the byte)
+        .i_aux(), //for AXI-interface compatibility (given upon strobe)
+        // Wishbone outputs
+        .o_wb_stall(o_wb_stall), //1 = busy, cannot accept requests
+        .o_wb_ack(o_wb_ack), //1 = read/write request has completed
+        .o_wb_data(o_wb_data), //read data, for a 4:1 controller data width is 8 times the number of pins on the device
+        // PHY Interface (to be added later)
+        .o_ddr3_clk_p(o_ddr3_clk_p),
+        .o_ddr3_clk_n(o_ddr3_clk_n),
+        .o_ddr3_cke(ck_en), // CKE
+        .o_ddr3_cs_n(cs_n), // chip select signal
+        .o_ddr3_odt(odt), // on-die termination
+        .o_ddr3_ras_n(ras_n), // RAS#
+        .o_ddr3_cas_n(cas_n), // CAS#
+        .o_ddr3_we_n(we_n), // WE#
+        .o_ddr3_reset_n(reset_n),
+        .o_ddr3_addr(addr),
+        .o_ddr3_ba_addr(ba_addr),
+        .io_ddr3_dq(dq),
+        .io_ddr3_dqs(dqs),
+        .io_ddr3_dqs_n(dqs_n)
+        ////////////////////////////////////
+    );
+    
+    always #2500 i_controller_clk = !i_controller_clk;
+    always #625 i_ddr3_clk = !i_ddr3_clk;
+    initial begin
+        i_controller_clk = 1;
+        i_ddr3_clk = 1;
+    end
+    integer stored_time = 0;
+    always begin
+        if($rtoi($time/1000) != $rtoi(stored_time/1000)) begin
+            $write("%t ", $time);
+            stored_time = $time;
+        end
+        #10;
+    end
+    // DDR3 Device 
+    ddr3 ddr3_0(
+        .rst_n(reset_n),
+        .ck(o_ddr3_clk_p),
+        .ck_n(o_ddr3_clk_n),
+        .cke(ck_en),
+        .cs_n(cs_n),
+        .ras_n(ras_n),
+        .cas_n(cas_n),
+        .we_n(we_n),
+        .dm_tdqs(),
+        .ba(ba_addr),
+        .addr(addr),
+        .dq(dq),
+        .dqs(dqs),
+        .dqs_n(dqs_n),
+        .tdqs_n(),
+        .odt(odt)
+    );
+    initial begin
+        @(negedge i_controller_clk)
+        i_rst_n = 0;
+        i_wb_cyc = 0;
+        i_wb_stb = 0;
+        i_wb_we = 0;
+        i_wb_addr = 0;
+        i_wb_data = 0;
+        @(negedge i_controller_clk)
+        i_rst_n = 1;
+        
+        wait(ddr3_controller.state_calibrate == ddr3_controller.DONE_CALIBRATE);
+        // burst read 1
+        wait(!o_wb_stall);
+        @(negedge i_controller_clk);
+        i_wb_cyc = 1;
+        i_wb_stb = 1;
+        i_wb_we = 1;
+        i_wb_addr = 0;
+        i_wb_data = "_ANGELO_";//64'h88_77_66_55_44_33_22_11;
+        @(negedge i_controller_clk);
+        i_wb_addr = 1;
+        i_wb_data = "_JACOBO_";//64'h00_ff_ee_dd_cc_bb_aa_99;
+        @(negedge i_controller_clk);
+        i_wb_stb = 0;
+        i_wb_data = 0;
+        /*
+        #100_000;
+        wait(!o_wb_stall);
+        i_wb_stb = 1;
+        i_wb_data = 64'h88_77_66_55_44_33_22_11;
+        @(negedge i_controller_clk);
+        i_wb_data = 64'h00_ff_ee_dd_cc_bb_aa_99;
+        @(negedge i_controller_clk);
+        i_wb_data = 64'h88_77_66_55_44_33_22_11;
+        @(negedge i_controller_clk);
+        i_wb_data = 64'h00_ff_ee_dd_cc_bb_aa_99;
+        @(negedge i_controller_clk);
+        i_wb_data = 64'h88_77_66_55_44_33_22_11;
+        @(negedge i_controller_clk);
+        i_wb_data = 64'h00_ff_ee_dd_cc_bb_aa_99;
+        i_wb_stb = 0;
+        */
+        wait(!o_wb_stall);
+        @(negedge i_controller_clk);
+        i_wb_stb = 1;
+        i_wb_we = 0;
+        i_wb_addr = 0;
+        //i_wb_data = 64'h88_77_66_55_44_33_22_11;
+        @(negedge i_controller_clk);
+        i_wb_addr = 1;
+        @(negedge i_controller_clk);
+        i_wb_stb = 0;
+        //wait(ddr3_controller.o_wb_ack);
+        
+        #100_000;
+        $stop;
+    end
+    
+    
+endmodule