507 lines
34 KiB
Plaintext
507 lines
34 KiB
Plaintext
0001 DmpCeff.cc:1597 cell %s delay model not supported on SPF parasitics by DMP delay calculator
|
|
0002 Liberty.cc:770 cell %s/%s port %s not found in cell %s/%s.
|
|
0003 Liberty.cc:796 cell %s/%s %s -> %s timing group %s not found in cell %s/%s.
|
|
0004 Liberty.cc:1746 cell %s/%s %s -> %s latch enable %s_edge is inconsistent with %s -> %s setup_%s check.
|
|
0005 Liberty.cc:1760 cell %s/%s %s -> %s latch enable %s_edge is inconsistent with latch group enable function positive sense.
|
|
0006 Liberty.cc:1768 cell %s/%s %s -> %s latch enable %s_edge is inconsistent with latch group enable function negative sense.
|
|
0007 LibertyExpr.cc:82 %s references unknown port %s.
|
|
0008 ConcreteNetwork.cc:1917 cell type %s can not be linked.
|
|
0009 CycleAccting.cc:87 No common period was found between clocks %s and %s.
|
|
0010 Genclks.cc:274 no master clock found for generated clock %s.
|
|
0013 Genclks.cc:938 generated clock %s source pin %s missing paths from master clock %s.
|
|
0015 Sim.cc:865 propagated logic value %c differs from constraint value of %c on pin %s.
|
|
0016 LibertyReader.cc:1037 default_max_fanout is 0.0.
|
|
0017 Sta.cc:2093 '%s' is not a valid endpoint.
|
|
0018 Sta.cc:2017 '%s' is not a valid start point.
|
|
0021 SpefParse.yy:805 %d is not positive.
|
|
0022 SpefParse.yy:814 %.4f is not positive.
|
|
0023 SpefParse.yy:820 %.4f is not positive.
|
|
0024 WritePathSpice.cc:508 pg_pin %s/%s voltage %s not found,
|
|
0025 WritePathSpice.cc:515 Liberty pg_port %s/%s missing voltage_name attribute,
|
|
0026 WritePathSpice.cc:1094 %s pg_port %s not found,
|
|
0027 WritePathSpice.cc:1149 no register/latch found for path from %s to %s,
|
|
0028 WritePathSpice.cc:1615 The subkct file %s is missing definitions for %s
|
|
0029 WritePathSpice.cc:1713 subckt %s port %s has no corresponding liberty port, pg_port and is not power or ground.
|
|
0030 LibertyReader.cc:631 library missing name.
|
|
0031 LibertyReader.cc:657 default_wire_load %s not found.
|
|
0032 LibertyReader.cc:668 default_wire_selection %s not found.
|
|
0033 LibertyReader.cc:690 input_threshold_pct_%s not found.
|
|
0034 LibertyReader.cc:694 output_threshold_pct_%s not found.
|
|
0035 LibertyReader.cc:698 slew_lower_threshold_pct_%s not found.
|
|
0036 LibertyReader.cc:702 slew_upper_threshold_pct_%s not found.
|
|
0037 LibertyReader.cc:707 Library %s is missing one or more thresholds.
|
|
0038 LibertyReader.cc:786 unknown unit multiplier %s.
|
|
0039 LibertyReader.cc:807 unknown unit scale %c.
|
|
0040 LibertyReader.cc:810 unknown unit suffix %s.
|
|
0041 LibertyReader.cc:836 capacitive_load_units are not ff or pf.
|
|
0042 LibertyReader.cc:839 capacitive_load_units are not a string.
|
|
0043 LibertyReader.cc:842 capacitive_load_units missing suffix.
|
|
0044 LibertyReader.cc:845 capacitive_load_units scale is not a float.
|
|
0045 LibertyReader.cc:848 capacitive_load_units missing scale and suffix.
|
|
0046 LibertyReader.cc:851 capacitive_load_unit missing values suffix.
|
|
0047 LibertyReader.cc:869 delay_model %s not supported.
|
|
0048 LibertyReader.cc:873 delay_model %s not supported.
|
|
0049 LibertyReader.cc:877 delay_model %s not supported.
|
|
0050 LibertyReader.cc:882 delay_model %s not supported.
|
|
.
|
|
0051 LibertyReader.cc:885 unknown delay_model %s
|
|
.
|
|
0052 LibertyReader.cc:904 unknown bus_naming_style format.
|
|
0053 LibertyReader.cc:597 library %s already exists.
|
|
0054 LibertyReader.cc:925 voltage_map voltage is not a float.
|
|
0055 LibertyReader.cc:928 voltage_map missing voltage.
|
|
0056 LibertyReader.cc:931 voltage_map supply name is not a string.
|
|
0057 LibertyReader.cc:934 voltage_map missing supply name and voltage.
|
|
0058 LibertyReader.cc:937 voltage_map missing values suffix.
|
|
0059 LibertyReader.cc:1155 default_wire_load_mode %s not found.
|
|
0060 LibertyReader.cc:680 default_operating_condition %s not found.
|
|
0061 LibertyReader.cc:1326 table template missing name.
|
|
0062 LibertyReader.cc:1371 missing variable_%d attribute.
|
|
0063 LibertyReader.cc:1414 axis type %s not supported.
|
|
0064 LibertyReader.cc:1474 bus type %s missing bit_from.
|
|
0065 LibertyReader.cc:1476 bus type %s missing bit_to.
|
|
0066 LibertyReader.cc:1480 type missing name.
|
|
0067 LibertyReader.cc:1507 scaling_factors do not have a name.
|
|
0068 LibertyReader.cc:1675 operating_conditions missing name.
|
|
0069 LibertyReader.cc:1745 wire_load missing name.
|
|
0070 LibertyReader.cc:1788 fanout_length is missing length and fanout.
|
|
0071 LibertyReader.cc:1803 wire_load_selection missing name.
|
|
0072 LibertyReader.cc:1834 wireload %s not found.
|
|
0074 LibertyReader.cc:1841 wire_load_from_area min not a float.
|
|
0075 LibertyReader.cc:1844 wire_load_from_area max not a float.
|
|
0076 LibertyReader.cc:1847 wire_load_from_area missing parameters.
|
|
0077 LibertyReader.cc:1850 wire_load_from_area missing parameters.
|
|
0078 LibertyReader.cc:1867 cell missing name.
|
|
0079 LibertyReader.cc:1890 cell %s ocv_derate_group %s not found.
|
|
0080 LibertyReader.cc:1926 port %s function size does not match port size.
|
|
0081 LibertyReader.cc:1994 %s %s bus width mismatch.
|
|
0082 LibertyReader.cc:2005 %s %s bus width mismatch.
|
|
0083 LibertyReader.cc:2015 clear
|
|
0084 LibertyReader.cc:2025 preset
|
|
0085 LibertyReader.cc:2061 latch enable function is non-unate for port %s.
|
|
0086 LibertyReader.cc:2066 latch enable function is unknown for port %s.
|
|
0087 LibertyReader.cc:2142 operating conditions %s not found.
|
|
0088 LibertyReader.cc:2145 scaled_cell missing operating condition.
|
|
0089 LibertyReader.cc:2148 scaled_cell cell %s has not been defined.
|
|
0090 LibertyReader.cc:2151 scaled_cell missing name.
|
|
0091 LibertyReader.cc:2177 scaled_cell %s, %s port functions do not match cell port functions.
|
|
0092 LibertyReader.cc:2182 scaled_cell ports do not match cell ports.
|
|
0093 LibertyReader.cc:2184 scaled_cell %s, %s timing does not match cell timing.
|
|
0094 LibertyReader.cc:2203 combinational timing to an input port.
|
|
0095 LibertyReader.cc:2294 missing %s_transition.
|
|
0096 LibertyReader.cc:2296 missing cell_%s.
|
|
0099 LibertyReader.cc:2894 scaling_factors %s not found.
|
|
0100 LibertyReader.cc:2937 pin name is not a string.
|
|
0101 LibertyReader.cc:2956 pin name is not a string.
|
|
0102 LibertyReader.cc:2972 pin name is not a string.
|
|
0103 LibertyReader.cc:3050 bus %s bus_type not found.
|
|
0104 LibertyReader.cc:3106 bus_type %s not found.
|
|
0105 LibertyReader.cc:3109 bus_type is not a string.
|
|
0106 LibertyReader.cc:3127 bundle %s member not found.
|
|
0107 LibertyReader.cc:3154 member is not a string.
|
|
0108 LibertyReader.cc:3161 members attribute is missing values.
|
|
0109 LibertyReader.cc:3212 unknown port direction.
|
|
0110 LibertyReader.cc:3580 pulse_latch unknown pulse type.
|
|
0111 LibertyReader.cc:3958 unknown timing_type %s.
|
|
0112 LibertyReader.cc:3978 unknown timing_sense %s.
|
|
0113 LibertyReader.cc:4018 mode value is not a string.
|
|
0114 LibertyReader.cc:4021 missing mode value.
|
|
0115 LibertyReader.cc:4024 mode name is not a string.
|
|
0116 LibertyReader.cc:4027 mode missing values.
|
|
0117 LibertyReader.cc:4030 mode missing mode name and value.
|
|
0118 LibertyReader.cc:2541 unsupported model axis.
|
|
0119 LibertyReader.cc:4133 unsupported model axis.
|
|
0120 LibertyReader.cc:4162 unsupported model axis.
|
|
0121 LibertyReader.cc:4197 unsupported model axis.
|
|
0122 LibertyReader.cc:4252 table template %s not found.
|
|
0123 LibertyReader.cc:4331 %s is missing values.
|
|
0124 LibertyReader.cc:4356 %s is not a list of floats.
|
|
0125 LibertyReader.cc:4358 table row has %u columns but axis has %d.
|
|
0126 LibertyReader.cc:4368 table has %u rows but axis has %d.
|
|
0127 LibertyReader.cc:4421 lut output is not a string.
|
|
0128 LibertyReader.cc:4463 mode definition missing name.
|
|
0129 LibertyReader.cc:4480 mode value missing name.
|
|
0130 LibertyReader.cc:4494 when attribute inside table model.
|
|
0131 LibertyReader.cc:4543 %s attribute is not a string.
|
|
0132 LibertyReader.cc:4546 %s is not a simple attribute.
|
|
0133 LibertyReader.cc:4569 %s is not a simple attribute.
|
|
0134 LibertyReader.cc:4582 %s is not a simple attribute.
|
|
0135 LibertyReader.cc:4606 %s value %s is not a float.
|
|
0136 LibertyReader.cc:4635 %s missing values.
|
|
0137 LibertyReader.cc:4639 %s missing values.
|
|
0138 LibertyReader.cc:4642 %s is not a complex attribute.
|
|
0139 LibertyReader.cc:4668 %s is not a float.
|
|
0140 LibertyReader.cc:4691 %s is missing values.
|
|
0141 LibertyReader.cc:4694 %s has more than one string.
|
|
0142 LibertyReader.cc:4703 %s is missing values.
|
|
0143 LibertyReader.cc:4728 %s attribute is not boolean.
|
|
0144 LibertyReader.cc:4731 %s attribute is not boolean.
|
|
0145 LibertyReader.cc:4734 %s is not a simple attribute.
|
|
0146 LibertyReader.cc:4750 attribute %s value %s not recognized.
|
|
0147 LibertyReader.cc:4781 unknown early/late value.
|
|
0148 LibertyReader.cc:5007 OCV derate group named %s not found.
|
|
0149 LibertyReader.cc:5023 ocv_derate missing name.
|
|
0150 LibertyReader.cc:5076 unknown rise/fall.
|
|
0151 LibertyReader.cc:5096 unknown derate type.
|
|
0152 LibertyReader.cc:5128 unsupported model axis.
|
|
0153 LibertyReader.cc:5160 unsupported model axis.
|
|
0154 LibertyReader.cc:5192 unsupported model axis.
|
|
0155 LibertyReader.cc:5263 unknown pg_type.
|
|
0156 LibertyReader.cc:5658 port %s subscript out of range.
|
|
0157 LibertyReader.cc:5662 port range %s of non-bus port %s.
|
|
0158 LibertyReader.cc:5676 port %s not found.
|
|
0159 LibertyReader.cc:5746 port %s not found.
|
|
0160 LibertyReader.cc:1022 default_max_transition is 0.0.
|
|
0161 LibertyReader.cc:3468 max_transition is 0.0.
|
|
0162 LibertyReader.cc:4566 %s attribute is not an integer.
|
|
0163 LibertyReader.cc:1127 default_fanout_load is 0.0.
|
|
0164 LibertyReader.cc:2316 timing group from output port.
|
|
0165 LibertyReader.cc:2326 timing group from output port.
|
|
0166 LibertyReader.cc:2336 timing group from output port.
|
|
0167 LibertyReader.cc:2354 timing group from output port.
|
|
0168 LibertyReader.cc:2369 timing group from output port.
|
|
0169 LibertyReader.cc:4438 cell %s test_cell redefinition.
|
|
0170 LibertyReader.cc:3877 timing group missing related_pin/related_bus_pin.
|
|
0179 SpefReader.cc:734 %s.
|
|
0190 VerilogReader.cc:1782 %s is not a verilog module.
|
|
0191 VerilogReader.cc:1787 %s is not a verilog module.
|
|
0201 StaTcl.i:118 no network has been linked.
|
|
0202 StaTcl.i:132 network does not support edits.
|
|
0204 StaTcl.i:4123 POCV support requires compilation with SSTA=1.
|
|
0206 LibertyExpr.cc:175 %s %s.
|
|
0207 GraphDelayCalc1.cc:738 port not found in cell
|
|
0208 Graph.cc:793 arc_delay_annotated array bounds exceeded
|
|
0209 Graph.cc:808 arc_delay_annotated array bounds exceeded
|
|
0210 Graph.cc:820 arc_delay_annotated array bounds exceeded
|
|
0211 SdcNetwork.cc:1095 inst path string lenth estimate busted
|
|
0212 SdcNetwork.cc:1167 inst path string lenth estimate exceeded
|
|
0213 Sdc.cc:4021 group path name and is_default are mutually exclusive.
|
|
0214 WriteSdc.cc:1254 unknown exception type
|
|
0215 WriteSdc.cc:1795 illegal set_logic value
|
|
0216 WriteSdc.cc:1836 invalid set_case_analysis value
|
|
0228 Graph.cc:833 arc_delay_annotated array bounds exceeded
|
|
0251 PathEnumed.cc:126 enumerated path required time
|
|
0252 PathEnumed.cc:135 enumerated path required time
|
|
0253 PathGroup.cc:399 unknown path end type
|
|
0254 PathVertexRep.cc:145 tag group missing tag
|
|
0255 ReportPath.cc:287 unsupported path type
|
|
0256 ReportPath.cc:308 unsupported path type
|
|
0257 ReportPath.cc:347 unsupported path type
|
|
0259 ReportPath.cc:2376 unsupported path type
|
|
0260 Search.cc:2655 max tag group index exceeded
|
|
0261 Search.cc:2891 max tag index exceeded
|
|
0262 Search.cc:3618 unexpected filter path
|
|
0263 Search.cc:3786 tns incr existing vertex
|
|
0264 Sta.cc:4190 corresponding timing arc set not found in equiv cells
|
|
0265 TagGroup.cc:297 tag group missing tag
|
|
0266 Sta.cc:2090 '%s' is not a valid endpoint.
|
|
0267 Sta.cc:2014 '%s' is not a valid start point.
|
|
0272 StaTcl.i:4109 unknown common clk pessimism mode.
|
|
0273 StaTcl.i:5055 unknown clock sense
|
|
0299 Power.tcl:241 activity cannot be set on clock ports.
|
|
0300 CmdUtil.tcl:44 no commands match '$pattern'.
|
|
0301 Power.tcl:218 activity should be 0.0 to 1.0 or 2.0
|
|
0302 Power.tcl:226 duty should be 0.0 to 1.0
|
|
0303 Sdc.tcl:1586 -clock ignored for clock objects.
|
|
0304 Sdc.tcl:2178 -from/-to keywords ignored for lib_pin, port and pin arguments.
|
|
0305 CmdArgs.tcl:166 object '$obj' not found.
|
|
0313 CmdArgs.tcl:842 unsupported object type $object_type.
|
|
0314 CmdArgs.tcl:857 $arg_name must be a single net.
|
|
0315 CmdArgs.tcl:863 $arg_name '$object_type' is not a net.
|
|
0316 CmdArgs.tcl:868 $arg_name '$arg' not found.
|
|
0318 Search.tcl:1057 unknown path group '$name'.
|
|
0319 Sdc.tcl:288 $unit scale [format %.0e $scale] does not match library scale [format %.0e $unit_scale].
|
|
0320 Sdc.tcl:437 current_design for other than top cell not supported.
|
|
0321 Sdc.tcl:474 patterns argument not supported with -of_objects.
|
|
0322 Sdc.tcl:509 instance '$pattern' not found.
|
|
0323 Sdc.tcl:570 clock '$pattern' not found.
|
|
0324 Sdc.tcl:597 positional arguments not supported with -of_objects.
|
|
0325 Sdc.tcl:623 library '$lib_name' not found.
|
|
0326 Sdc.tcl:635 cell '$cell_pattern' not found.
|
|
0327 Sdc.tcl:682 library/cell/port '$pattern' not found.
|
|
0328 Sdc.tcl:702 port '$port_pattern' not found.
|
|
0329 Sdc.tcl:707 library '$lib_name' not found.
|
|
0330 Sdc.tcl:717 -nocase ignored without -regexp.
|
|
0331 Sdc.tcl:743 library '$pattern' not found.
|
|
0332 Sdc.tcl:806 patterns argument not supported with -of_objects.
|
|
0333 Sdc.tcl:830 net '$pattern' not found.
|
|
0334 Sdc.tcl:859 patterns argument not supported with -of_objects.
|
|
0335 Sdc.tcl:896 pin '$pattern' not found.
|
|
0336 Sdc.tcl:953 patterns argument not supported with -of_objects.
|
|
0337 Sdc.tcl:967 port '$pattern' not found.
|
|
0338 Sdc.tcl:1065 non-increasing clock -waveform edge times.
|
|
0339 Sdc.tcl:1068 -waveform time greater than two periods.
|
|
0341 Sdc.tcl:1443 extra positional argument $arg.
|
|
0342 Sdc.tcl:1536 -clock ignored for clock objects.
|
|
0343 Sdc.tcl:1626 set_sense -type data not supported.
|
|
0344 Sdc.tcl:1641 set_clock_sense is deprecated as of SDC 2.1. Use set_sense -type clock.
|
|
0345 Sdc.tcl:1653 -pulse argument not supported.
|
|
0346 Sdc.tcl:1662 -positive, -negative, -stop_propagation and -pulse are mutually exclusive.
|
|
0347 Sdc.tcl:1675 hierarchical pin '[get_full_name $pin]' not supported.
|
|
0348 Sdc.tcl:2041 -from/-to keywords ignored for lib_pin, port and pin arguments.
|
|
0349 Sdc.tcl:1441 unknown keyword argument $arg.
|
|
0350 Sdc.tcl:2288 -from, -through or -to required.
|
|
0351 Sdc.tcl:2367 -source_latency_included ignored with -reference_pin.
|
|
0352 Sdc.tcl:2370 -network_latency_included ignored with -reference_pin.
|
|
0353 Sdc.tcl:2389 $cmd not allowed on [pin_direction $pin] port '[get_full_name $pin]'.
|
|
0354 Sdc.tcl:2391 $cmd relative to a clock defined on the same port/pin not allowed.
|
|
0355 Sdc.tcl:2445 '$args' ignored.
|
|
0356 Sdc.tcl:2575 '$args' ignored.
|
|
0357 Sdc.tcl:2710 virtual clock [get_name $clk] can not be propagated.
|
|
0358 Sdc.tcl:2884 -multiply_by ignored.
|
|
0359 Sdc.tcl:2887 -dont_scale ignored.
|
|
0360 Sdc.tcl:2890 -no_design_rule ignored.
|
|
0361 Sdc.tcl:2937 -clock not supported.
|
|
0362 Sdc.tcl:2940 -clock_fall not supported.
|
|
0363 Sdc.tcl:2986 -pin_load not allowed for net objects.
|
|
0364 Sdc.tcl:2989 -wire_load not allowed for net objects.
|
|
0365 Sdc.tcl:2992 -rise/-fall not allowed for net objects.
|
|
0366 Sdc.tcl:3125 -data_path, -clock_path, -rise, -fall ignored for ports and designs.
|
|
0367 Sdc.tcl:3196 derating factor greater than 2.0.
|
|
0368 Sdc.tcl:3233 -cell_delay and -cell_check flags ignored for net objects.
|
|
0369 Sdc.tcl:3303 no valid objects specified for $key.
|
|
0370 Sdc.tcl:3336 no valid objects specified for $key
|
|
0371 Sdc.tcl:3497 set_wire_load_min_block_size not supported.
|
|
0372 NetworkEdit.tcl:129 connect_pins is deprecated. Use connect_pin.
|
|
0373 Sdc.tcl:3647 define_corners must be called before read_liberty.
|
|
0374 Sta.cc:2416 maximum corner count exceeded
|
|
0400 Util.tcl:44 $cmd $key missing value.
|
|
0401 Util.tcl:61 $cmd $key missing value.
|
|
0402 Util.tcl:71 $cmd $arg is not a known keyword or flag.
|
|
0403 Util.tcl:93 $cmd $arg is not a known keyword or flag.
|
|
0404 CmdUtil.tcl:89 Usage: $cmd $cmd_args($cmd)
|
|
0405 CmdUtil.tcl:91 Usage: $cmd argument error
|
|
0406 Util.tcl:241 $cmd positional arguments not supported.
|
|
0407 Util.tcl:247 $cmd requires one positional argument.
|
|
0408 Util.tcl:254 $cmd requires zero or one positional arguments.
|
|
0409 Util.tcl:260 $cmd requires two positional arguments.
|
|
0410 Util.tcl:267 $cmd requires one or two positional arguments.
|
|
0411 Util.tcl:273 $cmd requires three positional arguments.
|
|
0412 Util.tcl:279 $cmd requires four positional arguments.
|
|
0413 Util.tcl:287 $cmd_arg '$arg' is not a float.
|
|
0414 Util.tcl:293 $cmd_arg '$arg' is not a positive float.
|
|
0415 Util.tcl:299 $cmd_arg '$arg' is not an integer.
|
|
0416 Util.tcl:305 $cmd_arg '$arg' is not a positive integer.
|
|
0417 Util.tcl:311 $cmd_arg '$arg' is not an integer greater than or equal to one.
|
|
0418 Util.tcl:317 $cmd_arg '$arg' is not between 0 and 100.
|
|
0419 Search.tcl:326 report_clock_skew -setup and -hold are mutually exclusive options.
|
|
0420 Search.tcl:136 $cmd -path_delay must be min, min_rise, min_fall, max, max_rise, max_fall or min_max.
|
|
0421 Search.tcl:146 $cmd command failed.
|
|
0422 Search.tcl:165 -endpoint_count must be a positive integer.
|
|
0423 Search.tcl:174 -group_count must be >= 1.
|
|
0424 Search.tcl:205 '$arg' is not a known keyword or flag.
|
|
0425 Search.tcl:207 positional arguments not supported.
|
|
0426 Search.tcl:510 analysis type single is not consistent with doing both setup/max and hold/min checks.
|
|
0427 Search.tcl:515 positional arguments not supported.
|
|
0428 DelayCalc.tcl:350 set_assigned_transition transition is not a float.
|
|
0430 Sdf.tcl:46 -cond_use min_max cannot be used with analysis type single.
|
|
0432 Sdf.tcl:157 SDF -divider must be / or .
|
|
0433 Parasitics.tcl:45 path instance '$path' not found.
|
|
0434 Parasitics.tcl:62 -reduce_to must be pi_elmore or pi_pole_residue2.
|
|
0435 DelayCalc.tcl:119 delay calculator $alg not found.
|
|
0436 Variables.tcl:45 sta_report_default_digits must be a positive integer.
|
|
0437 Variables.tcl:70 sta_crpr_mode must be pin or transition.
|
|
0438 Variables.tcl:187 $var_name value must be 0 or 1.
|
|
0439 CmdUtil.tcl:209 unsupported object type $list_type.
|
|
0440 Sta.tcl:158 -from/-to arguments not supported with -of_objects.
|
|
0441 Sta.tcl:286 unsupported -filter expression.
|
|
0442 DelayCalc.tcl:148 $cmd missing -from argument.
|
|
0443 DelayCalc.tcl:153 $cmd missing -to argument.
|
|
0444 DelayCalc.tcl:158 $cmd delay is not a float.
|
|
0445 DelayCalc.tcl:163 set_annotated_delay -cell and -net options are mutually excluive.
|
|
0446 DelayCalc.tcl:169 $cmd pin [get_full_name $pin] is not attached to instance [get_full_name $inst].
|
|
0447 DelayCalc.tcl:174 $cmd pin [get_full_name $pin] is not attached to instance [get_full_name $inst]
|
|
0448 DelayCalc.tcl:179 $cmd -cell or -net required.
|
|
0449 DelayCalc.tcl:243 $cmd missing -from argument.
|
|
0450 DelayCalc.tcl:252 $cmd -clock must be rise or fall.
|
|
0451 DelayCalc.tcl:259 $cmd missing -to argument.
|
|
0452 DelayCalc.tcl:274 $cmd missing -setup|-hold|-recovery|-removal check type..
|
|
0453 DelayCalc.tcl:282 $cmd check_value is not a float.
|
|
0454 Sdc.tcl:1472 the -all and -name options are mutually exclusive.
|
|
0455 Sdc.tcl:1475 either -all or -name options must be specified.
|
|
0456 Sdc.tcl:1483 one of -logically_exclusive, -physically_exclusive or -asynchronous is required.
|
|
0457 Sdc.tcl:1486 the keywords -logically_exclusive, -physically_exclusive and -asynchronous are mutually exclusive.
|
|
0458 Sdc.tcl:1598 -source '[$pin path_name]' is not a clock pin.
|
|
0459 Sdc.tcl:1866 -from/-to must be used together.
|
|
0460 Sdc.tcl:1886 -rise, -fall options not allowed for single clock uncertainty.
|
|
0461 Sdc.tcl:1987 missing -from, -rise_from or -fall_from argument.
|
|
0462 Sdc.tcl:1999 missing -to, -rise_to or -fall_to argument.
|
|
0463 Sdc.tcl:2230 -from/-to hierarchical instance not supported.
|
|
0464 Sdc.tcl:2632 $cmd command failed.
|
|
0465 Sdc.tcl:2639 positional arguments not supported.
|
|
0466 Sdc.tcl:2643 -from, -through or -to required.
|
|
0467 CmdArgs.tcl:108 unsupported object type $object_type.
|
|
0468 CmdArgs.tcl:405 $corner_name is not the name of process corner.
|
|
0469 CmdArgs.tcl:410 -corner keyword required with multi-corner analysis.
|
|
0470 CmdArgs.tcl:425 $corner_name is not the name of process corner.
|
|
0471 CmdArgs.tcl:430 missing -corner arg.
|
|
0472 CmdArgs.tcl:441 $corner_name is not the name of process corner.
|
|
0473 CmdArgs.tcl:458 $corner_name is not the name of process corner.
|
|
0474 CmdArgs.tcl:483 both -min and -max specified.
|
|
0475 CmdArgs.tcl:497 both -min and -max specified.
|
|
0476 CmdArgs.tcl:524 only one of -early and -late can be specified.
|
|
0477 CmdArgs.tcl:530 -early or -late must be specified.
|
|
0478 CmdArgs.tcl:537 both -early and -late specified.
|
|
0479 CmdArgs.tcl:552 $arg_name must be a single library.
|
|
0480 CmdArgs.tcl:558 $arg_name type '$object_type' is not a library.
|
|
0481 CmdArgs.tcl:563 library '$arg' not found.
|
|
0482 CmdArgs.tcl:580 $arg_name must be a single lib cell.
|
|
0483 CmdArgs.tcl:636 $arg_name must be a single instance.
|
|
0484 CmdArgs.tcl:642 $arg_name type '$object_type' is not an instance.
|
|
0485 CmdArgs.tcl:647 instance '$arg' not found.
|
|
0486 CmdArgs.tcl:666 $arg_name type '$object_type' is not an instance.
|
|
0487 CmdArgs.tcl:673 instance '$arg' not found.
|
|
0488 CmdArgs.tcl:734 $arg_name type '$object_type' is not a pin or port.
|
|
0489 CmdArgs.tcl:741 pin '$arg' not found.
|
|
0490 CmdArgs.tcl:761 $arg_name type '$object_type' is not a port.
|
|
0491 Property.tcl:32 $cmd object is null.
|
|
0492 Property.tcl:37 $cmd $type_key must be specified with object name argument.
|
|
0493 Property.tcl:80 get_property $object is not an object.
|
|
0494 Property.tcl:107 $object_type not supported.
|
|
0495 Property.tcl:110 $object_type '$object_name' not found.
|
|
0496 WritePathSpice.tcl:35 Directory $spice_dir not found.
|
|
0497 WritePathSpice.tcl:38 $spice_dir is not a directory.
|
|
0498 WritePathSpice.tcl:41 Cannot write in $spice_dir.
|
|
0499 WritePathSpice.tcl:44 No -spice_directory specified.
|
|
0500 WritePathSpice.tcl:50 -lib_subckt_file $lib_subckt_file is not readable.
|
|
0501 WritePathSpice.tcl:53 No -lib_subckt_file specified.
|
|
0502 WritePathSpice.tcl:59 -model_file $model_file is not readable.
|
|
0503 WritePathSpice.tcl:62 No -model_file specified.
|
|
0504 WritePathSpice.tcl:68 No -power specified.
|
|
0505 WritePathSpice.tcl:74 No -ground specified.
|
|
0506 WritePathSpice.tcl:78 No -path_args specified.
|
|
0507 WritePathSpice.tcl:83 No paths found for -path_args $path_args.
|
|
0508 Search.tcl:778 -min and -max cannot both be specified.
|
|
0509 Search.tcl:798 pin '$pin_arg' is hierarchical.
|
|
0510 Search.tcl:864 -format $format not recognized.
|
|
0511 Sdc.tcl:73 cannot open '$filename'.
|
|
0512 Sdc.tcl:128 incomplete command at end of file.
|
|
0513 Sdc.tcl:212 hierarchy separator must be one of '$sdc_dividers'.
|
|
0514 Sdc.tcl:259 unknown unit $unit '$suffix'.
|
|
0515 CmdUtil.tcl:161 unknown $unit unit '$suffix'.
|
|
0516 Sdc.tcl:543 unsupported instance -filter expression.
|
|
0517 Sdc.tcl:928 unsupported pin -filter expression.
|
|
0518 Sdc.tcl:1004 unsupported port -filter expression.
|
|
0519 Sdc.tcl:1037 -add requires -name.
|
|
0520 Sdc.tcl:1042 -name or port_pin_list must be specified.
|
|
0521 Sdc.tcl:1050 missing -period argument.
|
|
0522 Sdc.tcl:1056 -waveform edge_list must have an even number of edge times.
|
|
0523 Sdc.tcl:1126 empty ports/pins/nets argument.
|
|
0524 Sdc.tcl:1134 -add requires -name.
|
|
0525 Sdc.tcl:1139 name or port_pin_list must be specified.
|
|
0526 Sdc.tcl:1146 missing -source argument.
|
|
0527 Sdc.tcl:1161 -master_clock argument empty.
|
|
0528 Sdc.tcl:1164 -add requireds -master_clock.
|
|
0529 Sdc.tcl:1168 -multiply_by and -divide_by options are exclusive.
|
|
0530 Sdc.tcl:1172 -divide_by is not an integer greater than one.
|
|
0531 Sdc.tcl:1175 -combinational implies -divide_by 1.
|
|
0532 Sdc.tcl:1180 -multiply_by is not an integer greater than one.
|
|
0533 Sdc.tcl:1186 -duty_cycle is not a float between 0 and 100.
|
|
0534 Sdc.tcl:1192 -edges only supported for three edges.
|
|
0535 Sdc.tcl:1198 edges times are not monotonically increasing.
|
|
0536 Sdc.tcl:1207 -edge_shift length does not match -edges length.
|
|
0537 Sdc.tcl:1213 missing -multiply_by, -divide_by, -combinational or -edges argument.
|
|
0538 Sdc.tcl:1221 cannot specify -invert without -multiply_by, -divide_by or -combinational.
|
|
0539 Sdc.tcl:1227 -duty_cycle requires -multiply_by value.
|
|
0545 Sdc.tcl:1287 group_path command failed.
|
|
0546 Sdc.tcl:1294 positional arguments not supported.
|
|
0547 Sdc.tcl:1298 -from, -through or -to required.
|
|
0548 Sdc.tcl:1304 -name and -default are mutually exclusive.
|
|
0549 Sdc.tcl:1306 -name or -default option is required.
|
|
0550 Sdc.tcl:1347 cannot specify both -high and -low.
|
|
0551 Sdc.tcl:1355 missing -setup or -hold argument.
|
|
0552 Sdc.tcl:1369 -high and -low only permitted for pins and instances.
|
|
0553 Sdc.tcl:1376 -high and -low only permitted for pins and instances.
|
|
0554 Sdc.tcl:1419 one of -logically_exclusive, -physically_exclusive or -asynchronous is required.
|
|
0555 Sdc.tcl:1422 the keywords -logically_exclusive, -physically_exclusive and -asynchronous are mutually exclusive.
|
|
0556 Sdc.tcl:1550 -source '[get_full_name $pin]' is not a clock pin.
|
|
0557 Sdc.tcl:1557 -early/-late is only allowed with -source.
|
|
0558 Sdc.tcl:1630 set_sense -type clock|data
|
|
0559 Sdc.tcl:1699 transition time can not be specified for virtual clocks.
|
|
0560 Sdc.tcl:1732 missing uncertainty value.
|
|
0561 Sdc.tcl:1780 -from/-to must be used together.
|
|
0562 Sdc.tcl:1800 -rise, -fall options not allowed for single clock uncertainty.
|
|
0563 Sdc.tcl:1927 missing -from, -rise_from or -fall_from argument.
|
|
0564 Sdc.tcl:1939 missing -to, -rise_to or -fall_to argument.
|
|
0565 Sdc.tcl:2071 -from/-to hierarchical instance not supported.
|
|
0566 Sdc.tcl:2103 pin '[get_full_name $inst]${hierarchy_separator}${port_name}' not found.
|
|
0567 Sdc.tcl:2144 pin '[get_name $cell]${hierarchy_separator}${port_name}' not found.
|
|
0568 Sdc.tcl:2439 missing delay argument.
|
|
0569 Sdc.tcl:2570 missing path multiplier argument.
|
|
0570 Sdc.tcl:2582 cannot use -start with -end.
|
|
0571 Sdc.tcl:2752 value must be 0, zero, 1, one, rise, rising, fall, or falling.
|
|
0572 Sdc.tcl:2821 cell '$lib_name:$cell_name' not found.
|
|
0573 Sdc.tcl:2827 '$cell_name' not found.
|
|
0574 Sdc.tcl:2831 missing -lib_cell argument.
|
|
0575 Sdc.tcl:2839 port '$to_port_name' not found.
|
|
0576 Sdc.tcl:2851 -pin argument required for cells with multiple outputs.
|
|
0577 Sdc.tcl:2866 port '$from_port_name' not found.
|
|
0578 Sdc.tcl:3079 port '[get_name $port]' is not an input.
|
|
0579 Sdc.tcl:3453 operating condition '$op_cond_name' not found.
|
|
0580 Sdc.tcl:3471 operating condition '$op_cond_name' not found.
|
|
0581 Sdc.tcl:3485 -analysis_type must be single, bc_wc or on_chip_variation.
|
|
0582 Sdc.tcl:3510 mode must be top, enclosed or segmented.
|
|
0583 Sdc.tcl:3525 no wire load model specified.
|
|
0584 Sdc.tcl:3586 wire load selection group '$selection_name' not found.
|
|
0585 Sdc.tcl:3717 no default operating conditions found.
|
|
0586 NetworkEdit.tcl:99 unsupported object type $object_type.
|
|
0587 NetworkEdit.tcl:198 unsupported object type $object_type.
|
|
0588 NetworkEdit.tcl:216 unsupported object type $object_type.
|
|
0589 CmdUtil.tcl:226 unknown namespace $namespc.
|
|
0590 Network.tcl:35 instance $instance_path not found.
|
|
0591 Network.tcl:241 net $net_path not found.
|
|
0592 Network.tcl:244 net $net_path not found.
|
|
0593 Link.tcl:34 missing top_cell_name argument and no current_design.
|
|
0594 DelayNormal1.cc:203 unknown early/late value.
|
|
0595 DelayNormal2.cc:378 unknown early/late value.
|
|
0596 Sim.cc:210 unknown function operator
|
|
0597 EstimateParasitics.cc:188 load pin not leaf or top level
|
|
0600 Sdc.tcl:2284 '$args' ignored.
|
|
0601 Sdc.tcl:2913 set_fanout_load not supported.
|
|
0602 Sdc.tcl:3385 no valid objects specified for $key.
|
|
0604 Sdc.tcl:281 unknown $unit prefix '$prefix'.
|
|
0605 Sdc.tcl:3547 wire load model '$model_name' not found.
|
|
0606 Property.tcl:77 get_property unsupported object type $object_type.
|
|
0607 StaTcl.i:4359 unknown report path field %s
|
|
0608 StaTcl.i:4371 unknown report path field %s
|
|
0609 Search.tcl:411 -all_violators is deprecated. Use -violators
|
|
0610 Search.tcl:491 -max_transition deprecated. Use -max_slew.
|
|
0611 Search.tcl:496 -min_transition deprecated. Use -min_slew.
|
|
0612 Sdf.tcl:41 -cond_use must be min, max or min_max.
|
|
0616 Search.tcl:1008 specify one of -setup and -hold.
|
|
0617 Sdf.tcl:50 -analysis_type is deprecated. Use set_operating_conditions -analysis_type.
|
|
0618 DmpCeff.cc:1581 parasitic Pi model has NaNs.
|
|
0619 PathEnum.cc:474 path diversion missing edge.
|
|
0620 PathVertex.cc:236 missing arrivals.
|
|
0621 PathVertex.cc:250 missing arrivals.
|
|
0622 PathVertex.cc:279 missing requireds.
|
|
0623 PathVertexRep.cc:153 missing arrivals.
|
|
0624 PathVertexRep.cc:150 missing arrivals
|
|
0701 LibertyWriter.cc:411 %s/%s/%s timing model not supported.
|
|
0702 LibertyWriter.cc:431 3 axis table models not supported.
|
|
0703 LibertyWriter.cc:571 %s/%s/%s timing arc type %s not supported.
|
|
0704 LibertyWriter.cc:284 %s/%s bundled ports not supported.
|
|
0705 Liberty.cc:815 Liberty cell %s/%s for corner %s/%s not found.
|
|
0706 Parasitics.tcl:70 read_spef -increment is deprecated.
|
|
0710 LumpedCapDelayCalc.cc:169 gate delay input variable is NaN
|
|
0800 VcdReader.cc:110 unhandled vcd command.
|
|
0801 VcdReader.cc:146 timescale syntax error.
|
|
0802 VcdReader.cc:160 Unknown timescale unit.
|
|
0804 VcdReader.cc:212 Variable syntax error.
|
|
0805 Vcd.cc:172 Unknown variable %s ID %s
|
|
0806 ReadVcdActivities.cc:247 clock %s vcd period %s differs from SDC clock period %s
|
|
0807 Sdc.tcl:394 only one of -cells, -data_pins, -clock_pins, -async_pins, -output_pins are suppported.
|
|
0810 MakeTimingModel.cc:202 clock %s pin %s is inside model block.
|
|
0900 LibertyReader.cc:2834 level_shifter_type must be HL, LH, or HL_LH
|
|
0901 LibertyReader.cc:2870 switch_cell_type must be coarse_grain or fine_grain
|
|
0902 LibertyReader.cc:2452 unsupported model axis.
|
|
0903 LibertyReader.cc:4213 %s group not in timing group.
|
|
0904 LibertyReader.cc:2435 receiver_capacitance group not in timing or pin group.
|
|
0906 LibertyReader.cc:4106 unsupported model axis.
|
|
0907 LibertyReader.cc:2480 output_current_%s group not in timing group.
|
|
0908 LibertyReader.cc:2585 vector reference_time not found.
|
|
0912 LibertyReader.cc:2583 vector index_1 and index_2 must have exactly one value.
|
|
0913 LibertyReader.cc:2521 output current waveform %.2e %.2e not found.
|
|
0914 LibertyReader.cc:2618 normalized_driver_waveform variable_2 must be normalized_voltage
|
|
0915 LibertyReader.cc:2621 normalized_driver_waveform variable_1 must be input_net_transition
|