diff --git a/tests/silimate/extract_reduce.ys b/tests/silimate/extract_reduce.ys
new file mode 100644
index 000000000..1fbf1a06c
--- /dev/null
+++ b/tests/silimate/extract_reduce.ys
@@ -0,0 +1,605 @@
+###################################################################
+# Extract Reduce AND Gates Tests
+###################################################################
+
+log -header "Simple AND chain"
+log -push
+design -reset
+read_verilog <<EOF
+module top (
+  input wire [3:0] a,
+  output wire x
+);
+  assign x = a[0] & a[1] & a[2] & a[3];
+endmodule
+EOF
+check -assert
+
+# Check equivalence after extract_reduce
+equiv_opt -assert extract_reduce
+
+# Load design and run opt_clean to remove unnecessary wires
+design -load postopt
+opt_clean
+
+# Check final design has correct number of gates
+select -assert-count 0 t:$and
+select -assert-count 1 t:$reduce_and
+
+design -reset
+log -pop
+
+
+
+log -header "AND chain with multiple branches"
+log -push
+design -reset
+read_verilog <<EOF
+module top (
+  input wire [5:0] a,
+  output wire x
+);
+  wire w1, w2, w3, w4;
+
+  assign w1 = a[0] & a[1];
+  assign w2 = a[2] & a[3];
+  assign w3 = a[4] & a[5];
+  assign w4 = w1 & w2;
+  assign x = w3 & w4;
+endmodule
+EOF
+check -assert
+
+# Check equivalence after extract_reduce
+equiv_opt -assert extract_reduce
+
+# Load design and run opt_clean to remove unnecessary wires
+design -load postopt
+opt_clean
+
+# Check final design has correct number of gates
+select -assert-count 0 t:$and
+select -assert-count 1 t:$reduce_and
+
+design -reset
+log -pop
+
+
+
+log -header "No off-chain"
+log -push
+design -reset
+read_verilog <<EOF
+module top (
+  input wire [4:0] a,
+  output wire x,
+  output wire y
+);
+  wire w1, w2, w3;
+
+  assign w1 = a[0] & a[1];
+  assign w2 = w1 & a[2];
+  assign w3 = w2 & a[3];
+  assign x = w3 & a[4];
+
+  // Off-chain use of w2
+  assign y = w2;
+endmodule
+EOF
+check -assert
+
+# Check equivalence after extract_reduce
+equiv_opt -assert extract_reduce
+
+# Load design and run opt_clean to remove unnecessary wires
+design -load postopt
+opt_clean
+
+# Check final design has correct number of gates
+select -assert-count 0 t:$and
+select -assert-count 2 t:$reduce_and
+
+# Check that both gates are 3 bits wide
+select -assert-none t:$reduce_and r:A_WIDTH!=3 %i
+
+design -reset
+log -pop
+
+
+
+log -header "Allow off-chain for AND"
+log -push
+design -reset
+read_verilog <<EOF
+module top (
+  input wire [4:0] a,
+  output wire x,
+  output wire y
+);
+  wire w1, w2, w3;
+
+  assign w1 = a[0] & a[1];
+  assign w2 = w1 & a[2];
+  assign w3 = w2 & a[3];
+  assign x = w3 & a[4];
+
+  // Off-chain use of w2
+  assign y = w2;
+endmodule
+EOF
+check -assert
+
+# Check equivalence after extract_reduce
+equiv_opt -assert extract_reduce -allow-off-chain
+
+# Load design and run opt_clean to remove unnecessary wires
+design -load postopt
+opt_clean
+
+# Check final design has correct number of gates
+select -assert-count 0 t:$and
+select -assert-count 2 t:$reduce_and
+
+# Check that only one gate has a width of 5 and one gate has a width of 3
+select -assert-count 1 t:$reduce_and r:A_WIDTH=5 %i
+select -assert-count 1 t:$reduce_and r:A_WIDTH=3 %i
+
+design -reset
+log -pop
+
+###################################################################
+# Extract Reduce OR Gates Tests
+###################################################################
+
+log -header "Simple OR chain"
+log -push
+design -reset
+read_verilog <<EOF
+module top (
+  input wire [3:0] a,
+  output wire x
+);
+  assign x = a[0] | a[1] | a[2] | a[3];
+endmodule
+EOF
+check -assert
+
+# Check equivalence after extract_reduce
+equiv_opt -assert extract_reduce
+
+# Load design and run opt_clean to remove unnecessary wires
+design -load postopt
+opt_clean
+
+# Check final design has correct number of gates
+select -assert-count 0 t:$or
+select -assert-count 1 t:$reduce_or
+
+design -reset
+log -pop
+
+
+
+log -header "OR chain with multiple branches"
+log -push
+design -reset
+read_verilog <<EOF
+module top (
+  input wire [5:0] a,
+  output wire x
+);
+  wire w1, w2, w3, w4;
+
+  assign w1 = a[0] | a[1];
+  assign w2 = a[2] | a[3];
+  assign w3 = a[4] | a[5];
+  assign w4 = w1 | w2;
+  assign x = w3 | w4;
+endmodule
+EOF
+check -assert
+
+# Check equivalence after extract_reduce
+equiv_opt -assert extract_reduce
+
+# Load design and run opt_clean to remove unnecessary wires
+design -load postopt
+opt_clean
+
+# Check final design has correct number of gates
+select -assert-count 0 t:$or
+select -assert-count 1 t:$reduce_or
+
+design -reset
+log -pop
+
+
+
+log -header "No off-chain OR"
+log -push
+design -reset
+read_verilog <<EOF
+module top (
+  input wire [4:0] a,
+  output wire x,
+  output wire y
+);
+  wire w1, w2, w3;
+
+  assign w1 = a[0] | a[1];
+  assign w2 = w1 | a[2];
+  assign w3 = w2 | a[3];
+  assign x = w3 | a[4];
+
+  // Off-chain use of w2
+  assign y = w2;
+endmodule
+EOF
+check -assert
+
+# Check equivalence after extract_reduce
+equiv_opt -assert extract_reduce
+
+# Load design and run opt_clean to remove unnecessary wires
+design -load postopt
+opt_clean
+
+# Check final design has correct number of gates
+select -assert-count 0 t:$or
+select -assert-count 2 t:$reduce_or
+
+# Check that both gates are 3 bits wide
+select -assert-none t:$reduce_or r:A_WIDTH!=3 %i
+
+design -reset
+log -pop
+
+
+
+log -header "Allow off-chain for OR"
+log -push
+design -reset
+read_verilog <<EOF
+module top (
+  input wire [4:0] a,
+  output wire x,
+  output wire y
+);
+  wire w1, w2, w3;
+
+  assign w1 = a[0] | a[1];
+  assign w2 = w1 | a[2];
+  assign w3 = w2 | a[3];
+  assign x = w3 | a[4];
+
+  // Off-chain use of w2
+  assign y = w2;
+endmodule
+EOF
+check -assert
+
+# Check equivalence after extract_reduce
+equiv_opt -assert extract_reduce -allow-off-chain
+
+# Load design and run opt_clean to remove unnecessary wires
+design -load postopt
+opt_clean
+
+# Check final design has correct number of gates
+select -assert-count 0 t:$or
+select -assert-count 2 t:$reduce_or
+
+# Check that only one gate has a width of 5 and one gate has a width of 3
+select -assert-count 1 t:$reduce_or r:A_WIDTH=5 %i
+select -assert-count 1 t:$reduce_or r:A_WIDTH=3 %i
+
+design -reset
+log -pop
+
+###################################################################
+# Extract Reduce XOR Gates Tests
+###################################################################
+
+log -header "Simple XOR chain"
+log -push
+design -reset
+read_verilog <<EOF
+module top (
+  input wire [3:0] a,
+  output wire x
+);
+  assign x = a[0] ^ a[1] ^ a[2] ^ a[3];
+endmodule
+EOF
+check -assert
+
+# Check equivalence after extract_reduce
+equiv_opt -assert extract_reduce
+
+# Load design and run opt_clean to remove unnecessary wires
+design -load postopt
+opt_clean
+
+# Check final design has correct number of gates
+select -assert-count 0 t:$xor
+select -assert-count 1 t:$reduce_xor
+
+design -reset
+log -pop
+
+
+
+log -header "XOR chain with multiple branches"
+log -push
+design -reset
+read_verilog <<EOF
+module top (
+  input wire [5:0] a,
+  output wire x
+);
+  wire w1, w2, w3, w4;
+
+  assign w1 = a[0] ^ a[1];
+  assign w2 = a[2] ^ a[3];
+  assign w3 = a[4] ^ a[5];
+  assign w4 = w1 ^ w2;
+  assign x = w3 ^ w4;
+endmodule
+EOF
+check -assert
+
+# Check equivalence after extract_reduce
+equiv_opt -assert extract_reduce
+
+# Load design and run opt_clean to remove unnecessary wires
+design -load postopt
+opt_clean
+
+# Check final design has correct number of gates
+select -assert-count 0 t:$xor
+select -assert-count 1 t:$reduce_xor
+
+design -reset
+log -pop
+
+
+
+log -header "No off-chain XOR"
+log -push
+design -reset
+read_verilog <<EOF
+module top (
+  input wire [4:0] a,
+  output wire x,
+  output wire y
+);
+  wire w1, w2, w3;
+
+  assign w1 = a[0] ^ a[1];
+  assign w2 = w1 ^ a[2];
+  assign w3 = w2 ^ a[3];
+  assign x = w3 ^ a[4];
+
+  // Off-chain use of w2
+  assign y = w2;
+endmodule
+EOF
+check -assert
+
+# Check equivalence after extract_reduce
+equiv_opt -assert extract_reduce
+
+# Load design and run opt_clean to remove unnecessary wires
+design -load postopt
+
+opt_clean
+
+# Check final design has correct number of gates
+select -assert-count 0 t:$xor
+select -assert-count 2 t:$reduce_xor
+
+# Check that both gates are 3 bits wide
+select -assert-none t:$reduce_xor r:A_WIDTH!=3 %i
+
+design -reset
+log -pop
+
+
+
+log -header "Allow off-chain for XOR"
+log -push
+design -reset
+read_verilog <<EOF
+module top (
+  input wire [4:0] a,
+  output wire x,
+  output wire y
+);
+  wire w1, w2, w3;
+
+  assign w1 = a[0] ^ a[1];
+  assign w2 = w1 ^ a[2];
+  assign w3 = w2 ^ a[3];
+  assign x = w3 ^ a[4];
+
+  // Off-chain use of w2
+  assign y = w2;
+endmodule
+EOF
+check -assert
+
+# Check equivalence after extract_reduce
+equiv_opt -assert extract_reduce -allow-off-chain
+
+# Load design and run opt_clean to remove unnecessary wires
+design -load postopt
+opt_clean
+
+# Check final design has correct number of gates
+select -assert-count 0 t:$xor
+select -assert-count 2 t:$reduce_xor
+
+# Check that only one gate has a width of 5 and one gate has a width of 3
+select -assert-count 1 t:$reduce_xor r:A_WIDTH=5 %i
+select -assert-count 1 t:$reduce_xor r:A_WIDTH=3 %i
+
+design -reset
+log -pop
+
+
+
+###################################################################
+# Extract PMUX from MUX Chains Tests
+###################################################################
+
+log -header "Simple MUX chain to PMUX"
+log -push
+design -reset
+read_verilog <<EOF
+module top (
+  input wire [2:0] sel,
+  input wire [3:0] a,
+  output wire x
+);
+  wire w1, w2;
+
+  assign w1 = sel[0] ? a[1] : a[0];
+  assign w2 = sel[1] ? a[2] : w1;
+  assign x  = sel[2] ? a[3] : w2;
+endmodule
+EOF
+check -assert
+
+# Check equivalence after extract_reduce
+equiv_opt -assert extract_reduce
+
+# Load design and run opt_clean to remove unnecessary wires
+design -load postopt
+opt_clean
+
+# Check we got a single pmux
+select -assert-count 0 t:$mux
+select -assert-count 1 t:$pmux
+
+design -reset
+log -pop
+
+
+# TODO
+log -header "MUX chain with multiple branches"
+log -push
+design -reset
+read_verilog <<EOF
+module top (
+  input wire [2:0] sel,
+  input wire [3:0] a,
+  output wire x
+);
+  wire w1, w2;
+
+  assign w1 = sel[0] ? a[1] : a[0];
+  assign w2 = sel[1] ? a[2] : a[3];
+  assign x  = sel[2] ? w1 : w2;
+endmodule
+EOF
+check -assert
+
+# Check equivalence after extract_reduce
+equiv_opt -assert extract_reduce
+
+# Load design and run opt_clean to remove unnecessary wires
+design -load postopt
+opt_clean
+
+# Check we got a single pmux
+select -assert-count 0 t:$mux
+select -assert-count 1 t:$pmux
+
+design -reset
+log -pop
+
+
+
+log -header "No off-chain MUX chain"
+log -push
+design -reset
+read_verilog <<EOF
+module top (
+  input wire [3:0] sel,
+  input wire [4:0] a,
+  output wire x,
+  output wire y
+);
+  wire w1, w2, w3;
+
+  assign w1 = sel[0] ? a[1] : a[0];
+  assign w2 = sel[1] ? a[2] : w1;
+  assign w3 = sel[2] ? a[3] : w2;
+  assign x  = sel[3] ? a[4] : w3;
+
+  // Off-chain use of intermediate wire
+  assign y = w2;
+endmodule
+EOF
+check -assert
+
+# Check equivalence after extract_reduce
+equiv_opt -assert extract_reduce
+
+# Load design and run opt_clean to remove unnecessary wires
+design -load postopt
+opt_clean
+
+# Check we got two pmuxes
+select -assert-count 0 t:$mux
+select -assert-count 2 t:$pmux
+
+# Check that both pmuxes have input width of 3
+select -assert-none t:$pmux r:S_WIDTH!=3 %i
+
+design -reset
+log -pop
+
+
+
+
+log -header "Allow off-chain MUX chain"
+log -push
+design -reset
+read_verilog <<EOF
+module top (
+  input wire [3:0] sel,
+  input wire [4:0] a,
+  output wire x,
+  output wire y
+);
+  wire w1, w2, w3;
+
+  assign w1 = sel[0] ? a[1] : a[0];
+  assign w2 = sel[1] ? a[2] : w1;
+  assign w3 = sel[2] ? a[3] : w2;
+  assign x  = sel[3] ? a[4] : w3;
+
+  assign y = w2;
+endmodule
+EOF
+check -assert
+
+# Check equivalence after extract_reduce
+equiv_opt -assert extract_reduce -allow-off-chain
+
+# Load design and run opt_clean to remove unnecessary wires
+design -load postopt
+opt_clean
+
+# Check we got two $pmux
+select -assert-count 0 t:$mux
+select -assert-count 2 t:$pmux
+
+# Check that one pmux has an input width of 3 
+# and the other has an input width of 5
+select -assert-count 1 t:$pmux r:S_WIDTH=3 %i
+select -assert-count 1 t:$pmux r:S_WIDTH=5 %i
+
+design -reset
+log -pop