# Copyright (C) 2017-2020  The Project X-Ray Authors
#
# Use of this source code is governed by a ISC-style
# license that can be found in the LICENSE file or at
# https://opensource.org/licenses/ISC
#
# SPDX-License-Identifier: ISC
source "$::env(XRAY_DIR)/utils/utils.tcl"

create_project -force -part $::env(XRAY_PART) design design

read_verilog $::env(FUZDIR)/top.v
synth_design -top top

set_property -dict "PACKAGE_PIN $::env(XRAY_PIN_00) IOSTANDARD LVCMOS33" [get_ports i]
set_property -dict "PACKAGE_PIN $::env(XRAY_PIN_01) IOSTANDARD LVCMOS33" [get_ports o]

create_pblock roi
resize_pblock [get_pblocks roi] -add "$::env(XRAY_ROI)"

set_property CFGBVS VCCO [current_design]
set_property CONFIG_VOLTAGE 3.3 [current_design]
set_property BITSTREAM.GENERAL.PERFRAMECRC YES [current_design]
set_param tcl.collectionResultDisplayLimit 0

place_design
route_design

# write_checkpoint -force design.dcp

set fp [open "../todo.txt" r]
set todo_lines {}
for {gets $fp line} {$line != ""} {gets $fp line} {
    lappend todo_lines [split $line .]
}
close $fp

# each run can fail up to three times so we need to prepare 3*todo_lines tiles to work on
set tiles [expr 3 * [llength $todo_lines]]

set int_l_tiles [randsample_list $tiles [filter [pblock_tiles roi] {TYPE == INT_L}]]
set int_r_tiles [randsample_list $tiles [filter [pblock_tiles roi] {TYPE == INT_R}]]


for {set idx 0} {$idx < [llength $todo_lines]} {incr idx} {
    set line [lindex $todo_lines $idx]
    puts "== $idx: $line"

    set tile_type [lindex $line 0]
    set dst_wire [lindex $line 1]
    set src_wire [lindex $line 2]

    set mynet [create_net mynet_$idx]
    set mylut [create_cell -reference LUT1 mylut_$idx]

    if {$src_wire == "VCC_WIRE"} {
        set mytie [create_cell -reference VCC mytie_$idx]
        connect_net -net $mynet -objects "$mytie/P $mylut/I0"
    }

    if {$src_wire == "GND_WIRE"} {
        set mytie [create_cell -reference GND mytie_$idx]
        connect_net -net $mynet -objects "$mytie/G $mylut/I0"
    }

    set tries 0
    while {1} {
        set tile_idx [expr $tries + [expr $idx * 3]]
        incr tries

        if {$tile_type == "INT_L"} {set tile [lindex $int_l_tiles $tile_idx]; set other_tile [lindex $int_r_tiles $tile_idx]}
        if {$tile_type == "INT_R"} {set tile [lindex $int_r_tiles $tile_idx]; set other_tile [lindex $int_l_tiles $tile_idx]}

        set recv_site [get_sites -of_objects [get_site_pins -of_objects [get_nodes -downhill \
                -of_objects [get_nodes -of_objects [get_wires $other_tile/CLK*0]]]]]

        set_property -dict "LOC $recv_site BEL A6LUT" $mylut

        set rc [route_via $mynet "$tile/$src_wire $tile/$dst_wire" 0]
        if {$rc != 0} {
            puts "ROUTING DONE!"
            break
        }

        # fallback
        puts "WARNING: failed to route net"
        write_checkpoint -force route_todo_$idx.$tries.fail.dcp

        puts "Rolling back route"
        set_property is_route_fixed 0 $mynet
        set_property is_bel_fixed 0 $mylut
        set_property is_loc_fixed 1 $mylut
        route_design -unroute -nets $mynet

        # sometimes it gets stuck in specific src -> dst locations
        if {$tries >= 3} {
            error "ERROR: failed to route net after $tries tries"
        }
    }
}

route_design
write_checkpoint -force design.dcp
write_bitstream -force design.bit
write_pip_txtdata design.txt