0001 DmpCeff.cc:1597 cell %s delay model not supported on SPF parasitics by DMP delay calculator 0002 Liberty.cc:750 cell %s/%s port %s not found in cell %s/%s. 0003 Liberty.cc:776 cell %s/%s %s -> %s timing group %s not found in cell %s/%s. 0004 Liberty.cc:1728 cell %s/%s %s -> %s latch enable %s_edge is inconsistent with %s -> %s setup_%s check. 0005 Liberty.cc:1742 cell %s/%s %s -> %s latch enable %s_edge is inconsistent with latch group enable function positive sense. 0006 Liberty.cc:1750 cell %s/%s %s -> %s latch enable %s_edge is inconsistent with latch group enable function negative sense. 0007 LibertyExpr.cc:82 %s references unknown port %s. 0008 ConcreteNetwork.cc:1917 cell type %s can not be linked. 0009 CycleAccting.cc:87 No common period was found between clocks %s and %s. 0010 Genclks.cc:274 no master clock found for generated clock %s. 0013 Genclks.cc:938 generated clock %s source pin %s missing paths from master clock %s. 0015 Sim.cc:865 propagated logic value %c differs from constraint value of %c on pin %s. 0016 LibertyReader.cc:1049 default_max_fanout is 0.0. 0017 Sta.cc:2093 '%s' is not a valid endpoint. 0018 Sta.cc:2017 '%s' is not a valid start point. 0021 SpefParse.yy:805 %d is not positive. 0022 SpefParse.yy:814 %.4f is not positive. 0023 SpefParse.yy:820 %.4f is not positive. 0024 WritePathSpice.cc:458 pg_pin %s/%s voltage %s not found, 0025 WritePathSpice.cc:465 Liberty pg_port %s/%s missing voltage_name attribute, 0026 WritePathSpice.cc:1037 %s pg_port %s not found, 0027 WritePathSpice.cc:1092 no register/latch found for path from %s to %s, 0028 WritePathSpice.cc:1464 The subkct file %s is missing definitions for %s 0029 WritePathSpice.cc:1562 subckt %s port %s has no corresponding liberty port, pg_port and is not power or ground. 0030 LibertyReader.cc:628 library missing name. 0031 LibertyReader.cc:660 default_wire_load %s not found. 0032 LibertyReader.cc:671 default_wire_selection %s not found. 0033 LibertyReader.cc:693 input_threshold_pct_%s not found. 0034 LibertyReader.cc:697 output_threshold_pct_%s not found. 0035 LibertyReader.cc:701 slew_lower_threshold_pct_%s not found. 0036 LibertyReader.cc:705 slew_upper_threshold_pct_%s not found. 0037 LibertyReader.cc:710 Library %s is missing one or more thresholds. 0038 LibertyReader.cc:800 unknown unit multiplier %s. 0039 LibertyReader.cc:819 unknown unit scale %c. 0040 LibertyReader.cc:822 unknown unit suffix %s. 0041 LibertyReader.cc:848 capacitive_load_units are not ff or pf. 0042 LibertyReader.cc:851 capacitive_load_units are not a string. 0043 LibertyReader.cc:854 capacitive_load_units missing suffix. 0044 LibertyReader.cc:857 capacitive_load_units scale is not a float. 0045 LibertyReader.cc:860 capacitive_load_units missing scale and suffix. 0046 LibertyReader.cc:863 capacitive_load_unit missing values suffix. 0047 LibertyReader.cc:881 delay_model %s not supported. 0048 LibertyReader.cc:885 delay_model %s not supported. 0049 LibertyReader.cc:889 delay_model %s not supported. 0050 LibertyReader.cc:894 delay_model %s not supported. . 0051 LibertyReader.cc:897 unknown delay_model %s . 0052 LibertyReader.cc:916 unknown bus_naming_style format. 0053 LibertyReader.cc:594 library %s already exists. 0054 LibertyReader.cc:937 voltage_map voltage is not a float. 0055 LibertyReader.cc:940 voltage_map missing voltage. 0056 LibertyReader.cc:943 voltage_map supply name is not a string. 0057 LibertyReader.cc:946 voltage_map missing supply name and voltage. 0058 LibertyReader.cc:949 voltage_map missing values suffix. 0059 LibertyReader.cc:1167 default_wire_load_mode %s not found. 0060 LibertyReader.cc:683 default_operating_condition %s not found. 0061 LibertyReader.cc:1338 table template missing name. 0062 LibertyReader.cc:1383 missing variable_%d attribute. 0063 LibertyReader.cc:1426 axis type %s not supported. 0064 LibertyReader.cc:1486 bus type %s missing bit_from. 0065 LibertyReader.cc:1488 bus type %s missing bit_to. 0066 LibertyReader.cc:1492 type missing name. 0067 LibertyReader.cc:1519 scaling_factors do not have a name. 0068 LibertyReader.cc:1687 operating_conditions missing name. 0069 LibertyReader.cc:1757 wire_load missing name. 0070 LibertyReader.cc:1800 fanout_length is missing length and fanout. 0071 LibertyReader.cc:1815 wire_load_selection missing name. 0072 LibertyReader.cc:1846 wireload %s not found. 0074 LibertyReader.cc:1853 wire_load_from_area min not a float. 0075 LibertyReader.cc:1856 wire_load_from_area max not a float. 0076 LibertyReader.cc:1859 wire_load_from_area missing parameters. 0077 LibertyReader.cc:1862 wire_load_from_area missing parameters. 0078 LibertyReader.cc:1879 cell missing name. 0079 LibertyReader.cc:1902 cell %s ocv_derate_group %s not found. 0080 LibertyReader.cc:1938 port %s function size does not match port size. 0081 LibertyReader.cc:2006 %s %s bus width mismatch. 0082 LibertyReader.cc:2017 %s %s bus width mismatch. 0083 LibertyReader.cc:2027 clear 0084 LibertyReader.cc:2037 preset 0085 LibertyReader.cc:2073 latch enable function is non-unate for port %s. 0086 LibertyReader.cc:2078 latch enable function is unknown for port %s. 0087 LibertyReader.cc:2154 operating conditions %s not found. 0088 LibertyReader.cc:2157 scaled_cell missing operating condition. 0089 LibertyReader.cc:2160 scaled_cell cell %s has not been defined. 0090 LibertyReader.cc:2163 scaled_cell missing name. 0091 LibertyReader.cc:2189 scaled_cell %s, %s port functions do not match cell port functions. 0092 LibertyReader.cc:2194 scaled_cell ports do not match cell ports. 0093 LibertyReader.cc:2196 scaled_cell %s, %s timing does not match cell timing. 0094 LibertyReader.cc:2215 combinational timing to an input port. 0095 LibertyReader.cc:2306 missing %s_transition. 0096 LibertyReader.cc:2308 missing cell_%s. 0099 LibertyReader.cc:2900 scaling_factors %s not found. 0100 LibertyReader.cc:2943 pin name is not a string. 0101 LibertyReader.cc:2962 pin name is not a string. 0102 LibertyReader.cc:2978 pin name is not a string. 0103 LibertyReader.cc:3056 bus %s bus_type not found. 0104 LibertyReader.cc:3112 bus_type %s not found. 0105 LibertyReader.cc:3115 bus_type is not a string. 0106 LibertyReader.cc:3133 bundle %s member not found. 0107 LibertyReader.cc:3160 member is not a string. 0108 LibertyReader.cc:3167 members attribute is missing values. 0109 LibertyReader.cc:3218 unknown port direction. 0110 LibertyReader.cc:3586 pulse_latch unknown pulse type. 0111 LibertyReader.cc:3964 unknown timing_type %s. 0112 LibertyReader.cc:3984 unknown timing_sense %s. 0113 LibertyReader.cc:4024 mode value is not a string. 0114 LibertyReader.cc:4027 missing mode value. 0115 LibertyReader.cc:4030 mode name is not a string. 0116 LibertyReader.cc:4033 mode missing values. 0117 LibertyReader.cc:4036 mode missing mode name and value. 0118 LibertyReader.cc:2547 unsupported model axis. 0119 LibertyReader.cc:4139 unsupported model axis. 0120 LibertyReader.cc:4168 unsupported model axis. 0121 LibertyReader.cc:4203 unsupported model axis. 0122 LibertyReader.cc:4258 table template %s not found. 0123 LibertyReader.cc:4337 %s is missing values. 0124 LibertyReader.cc:4362 %s is not a list of floats. 0125 LibertyReader.cc:4364 table row has %u columns but axis has %d. 0126 LibertyReader.cc:4374 table has %u rows but axis has %d. 0127 LibertyReader.cc:4427 lut output is not a string. 0128 LibertyReader.cc:4469 mode definition missing name. 0129 LibertyReader.cc:4486 mode value missing name. 0130 LibertyReader.cc:4500 when attribute inside table model. 0131 LibertyReader.cc:4549 %s attribute is not a string. 0132 LibertyReader.cc:4552 %s is not a simple attribute. 0133 LibertyReader.cc:4575 %s is not a simple attribute. 0134 LibertyReader.cc:4588 %s is not a simple attribute. 0135 LibertyReader.cc:4612 %s value %s is not a float. 0136 LibertyReader.cc:4641 %s missing values. 0137 LibertyReader.cc:4645 %s missing values. 0138 LibertyReader.cc:4648 %s is not a complex attribute. 0139 LibertyReader.cc:4674 %s is not a float. 0140 LibertyReader.cc:4697 %s is missing values. 0141 LibertyReader.cc:4700 %s has more than one string. 0142 LibertyReader.cc:4709 %s is missing values. 0143 LibertyReader.cc:4734 %s attribute is not boolean. 0144 LibertyReader.cc:4737 %s attribute is not boolean. 0145 LibertyReader.cc:4740 %s is not a simple attribute. 0146 LibertyReader.cc:4756 attribute %s value %s not recognized. 0147 LibertyReader.cc:4786 unknown early/late value. 0148 LibertyReader.cc:5012 OCV derate group named %s not found. 0149 LibertyReader.cc:5028 ocv_derate missing name. 0150 LibertyReader.cc:5081 unknown rise/fall. 0151 LibertyReader.cc:5101 unknown derate type. 0152 LibertyReader.cc:5133 unsupported model axis. 0153 LibertyReader.cc:5165 unsupported model axis. 0154 LibertyReader.cc:5197 unsupported model axis. 0155 LibertyReader.cc:5268 unknown pg_type. 0156 LibertyReader.cc:5663 port %s subscript out of range. 0157 LibertyReader.cc:5667 port range %s of non-bus port %s. 0158 LibertyReader.cc:5681 port %s not found. 0159 LibertyReader.cc:5751 port %s not found. 0160 LibertyReader.cc:1034 default_max_transition is 0.0. 0161 LibertyReader.cc:3474 max_transition is 0.0. 0162 LibertyReader.cc:4572 %s attribute is not an integer. 0163 LibertyReader.cc:1139 default_fanout_load is 0.0. 0164 LibertyReader.cc:2328 timing group from output port. 0165 LibertyReader.cc:2338 timing group from output port. 0166 LibertyReader.cc:2348 timing group from output port. 0167 LibertyReader.cc:2366 timing group from output port. 0168 LibertyReader.cc:2381 timing group from output port. 0169 LibertyReader.cc:4444 cell %s test_cell redefinition. 0170 LibertyReader.cc:3883 timing group missing related_pin/related_bus_pin. 0179 SpefReader.cc:734 %s. 0190 VerilogReader.cc:1756 %s is not a verilog module. 0191 VerilogReader.cc:1761 %s is not a verilog module. 0201 StaTcl.i:118 no network has been linked. 0202 StaTcl.i:132 network does not support edits. 0204 StaTcl.i:4072 POCV support requires compilation with SSTA=1. 0206 LibertyExpr.cc:175 %s %s. 0207 GraphDelayCalc1.cc:738 port not found in cell 0208 Graph.cc:793 arc_delay_annotated array bounds exceeded 0209 Graph.cc:808 arc_delay_annotated array bounds exceeded 0210 Graph.cc:820 arc_delay_annotated array bounds exceeded 0211 SdcNetwork.cc:1077 inst path string lenth estimate busted 0212 SdcNetwork.cc:1149 inst path string lenth estimate exceeded 0213 Sdc.cc:4021 group path name and is_default are mutually exclusive. 0214 WriteSdc.cc:1254 unknown exception type 0215 WriteSdc.cc:1795 illegal set_logic value 0216 WriteSdc.cc:1836 invalid set_case_analysis value 0228 Graph.cc:833 arc_delay_annotated array bounds exceeded 0251 PathEnumed.cc:126 enumerated path required time 0252 PathEnumed.cc:135 enumerated path required time 0253 PathGroup.cc:399 unknown path end type 0254 PathVertexRep.cc:145 tag group missing tag 0255 ReportPath.cc:287 unsupported path type 0256 ReportPath.cc:308 unsupported path type 0257 ReportPath.cc:347 unsupported path type 0259 ReportPath.cc:2376 unsupported path type 0260 Search.cc:2628 max tag group index exceeded 0261 Search.cc:2860 max tag index exceeded 0262 Search.cc:3551 unexpected filter path 0263 Search.cc:3719 tns incr existing vertex 0264 Sta.cc:4180 corresponding timing arc set not found in equiv cells 0265 TagGroup.cc:297 tag group missing tag 0266 Sta.cc:2090 '%s' is not a valid endpoint. 0267 Sta.cc:2014 '%s' is not a valid start point. 0272 StaTcl.i:4058 unknown common clk pessimism mode. 0273 StaTcl.i:5003 unknown clock sense 0299 Power.tcl:241 activity cannot be set on clock ports. 0300 CmdUtil.tcl:44 no commands match '$pattern'. 0301 Power.tcl:218 activity should be 0.0 to 1.0 or 2.0 0302 Power.tcl:226 duty should be 0.0 to 1.0 0303 Sdc.tcl:1586 -clock ignored for clock objects. 0304 Sdc.tcl:2178 -from/-to keywords ignored for lib_pin, port and pin arguments. 0305 CmdArgs.tcl:166 object '$obj' not found. 0313 CmdArgs.tcl:842 unsupported object type $object_type. 0314 CmdArgs.tcl:857 $arg_name must be a single net. 0315 CmdArgs.tcl:863 $arg_name '$object_type' is not a net. 0316 CmdArgs.tcl:868 $arg_name '$arg' not found. 0318 Search.tcl:1067 unknown path group '$name'. 0319 Sdc.tcl:288 $unit scale [format %.0e $scale] does not match library scale [format %.0e $unit_scale]. 0320 Sdc.tcl:437 current_design for other than top cell not supported. 0321 Sdc.tcl:474 patterns argument not supported with -of_objects. 0322 Sdc.tcl:509 instance '$pattern' not found. 0323 Sdc.tcl:570 clock '$pattern' not found. 0324 Sdc.tcl:597 positional arguments not supported with -of_objects. 0325 Sdc.tcl:623 library '$lib_name' not found. 0326 Sdc.tcl:635 cell '$cell_pattern' not found. 0327 Sdc.tcl:682 library/cell/port '$pattern' not found. 0328 Sdc.tcl:702 port '$port_pattern' not found. 0329 Sdc.tcl:707 library '$lib_name' not found. 0330 Sdc.tcl:717 -nocase ignored without -regexp. 0331 Sdc.tcl:743 library '$pattern' not found. 0332 Sdc.tcl:806 patterns argument not supported with -of_objects. 0333 Sdc.tcl:830 net '$pattern' not found. 0334 Sdc.tcl:859 patterns argument not supported with -of_objects. 0335 Sdc.tcl:896 pin '$pattern' not found. 0336 Sdc.tcl:953 patterns argument not supported with -of_objects. 0337 Sdc.tcl:967 port '$pattern' not found. 0338 Sdc.tcl:1065 non-increasing clock -waveform edge times. 0339 Sdc.tcl:1068 -waveform time greater than two periods. 0341 Sdc.tcl:1443 extra positional argument $arg. 0342 Sdc.tcl:1536 -clock ignored for clock objects. 0343 Sdc.tcl:1626 set_sense -type data not supported. 0344 Sdc.tcl:1641 set_clock_sense is deprecated as of SDC 2.1. Use set_sense -type clock. 0345 Sdc.tcl:1653 -pulse argument not supported. 0346 Sdc.tcl:1662 -positive, -negative, -stop_propagation and -pulse are mutually exclusive. 0347 Sdc.tcl:1675 hierarchical pin '[get_full_name $pin]' not supported. 0348 Sdc.tcl:2041 -from/-to keywords ignored for lib_pin, port and pin arguments. 0349 Sdc.tcl:1441 unknown keyword argument $arg. 0350 Sdc.tcl:2288 -from, -through or -to required. 0351 Sdc.tcl:2367 -source_latency_included ignored with -reference_pin. 0352 Sdc.tcl:2370 -network_latency_included ignored with -reference_pin. 0353 Sdc.tcl:2389 $cmd not allowed on [pin_direction $pin] port '[get_full_name $pin]'. 0354 Sdc.tcl:2391 $cmd relative to a clock defined on the same port/pin not allowed. 0355 Sdc.tcl:2445 '$args' ignored. 0356 Sdc.tcl:2575 '$args' ignored. 0357 Sdc.tcl:2710 virtual clock [get_name $clk] can not be propagated. 0358 Sdc.tcl:2884 -multiply_by ignored. 0359 Sdc.tcl:2887 -dont_scale ignored. 0360 Sdc.tcl:2890 -no_design_rule ignored. 0361 Sdc.tcl:2937 -clock not supported. 0362 Sdc.tcl:2940 -clock_fall not supported. 0363 Sdc.tcl:2986 -pin_load not allowed for net objects. 0364 Sdc.tcl:2989 -wire_load not allowed for net objects. 0365 Sdc.tcl:2992 -rise/-fall not allowed for net objects. 0366 Sdc.tcl:3125 -data_path, -clock_path, -rise, -fall ignored for ports and designs. 0367 Sdc.tcl:3196 derating factor greater than 2.0. 0368 Sdc.tcl:3233 -cell_delay and -cell_check flags ignored for net objects. 0369 Sdc.tcl:3303 no valid objects specified for $key. 0370 Sdc.tcl:3336 no valid objects specified for $key 0371 Sdc.tcl:3497 set_wire_load_min_block_size not supported. 0372 NetworkEdit.tcl:129 connect_pins is deprecated. Use connect_pin. 0373 Sdc.tcl:3647 define_corners must be called before read_liberty. 0400 Util.tcl:44 $cmd $key missing value. 0401 Util.tcl:61 $cmd $key missing value. 0402 Util.tcl:71 $cmd $arg is not a known keyword or flag. 0403 Util.tcl:93 $cmd $arg is not a known keyword or flag. 0404 CmdUtil.tcl:89 Usage: $cmd $cmd_args($cmd) 0405 CmdUtil.tcl:91 Usage: $cmd argument error 0406 Util.tcl:241 $cmd positional arguments not supported. 0407 Util.tcl:247 $cmd requires one positional argument. 0408 Util.tcl:254 $cmd requires zero or one positional arguments. 0409 Util.tcl:260 $cmd requires two positional arguments. 0410 Util.tcl:267 $cmd requires one or two positional arguments. 0411 Util.tcl:273 $cmd requires three positional arguments. 0412 Util.tcl:279 $cmd requires four positional arguments. 0413 Util.tcl:287 $cmd_arg '$arg' is not a float. 0414 Util.tcl:293 $cmd_arg '$arg' is not a positive float. 0415 Util.tcl:299 $cmd_arg '$arg' is not an integer. 0416 Util.tcl:305 $cmd_arg '$arg' is not a positive integer. 0417 Util.tcl:311 $cmd_arg '$arg' is not an integer greater than or equal to one. 0418 Util.tcl:317 $cmd_arg '$arg' is not between 0 and 100. 0419 Search.tcl:336 report_clock_skew -setup and -hold are mutually exclusive options. 0420 Search.tcl:136 $cmd -path_delay must be min, min_rise, min_fall, max, max_rise, max_fall or min_max. 0421 Search.tcl:146 $cmd command failed. 0422 Search.tcl:165 -endpoint_count must be a positive integer. 0423 Search.tcl:174 -group_count must be >= 1. 0424 Search.tcl:205 '$arg' is not a known keyword or flag. 0425 Search.tcl:207 positional arguments not supported. 0426 Search.tcl:520 analysis type single is not consistent with doing both setup/max and hold/min checks. 0427 Search.tcl:525 positional arguments not supported. 0428 DelayCalc.tcl:350 set_assigned_transition transition is not a float. 0430 Sdf.tcl:46 -cond_use min_max cannot be used with analysis type single. 0432 Sdf.tcl:157 SDF -divider must be / or . 0433 Parasitics.tcl:45 path instance '$path' not found. 0434 Parasitics.tcl:62 -reduce_to must be pi_elmore or pi_pole_residue2. 0435 DelayCalc.tcl:119 delay calculator $alg not found. 0436 Variables.tcl:45 sta_report_default_digits must be a positive integer. 0437 Variables.tcl:70 sta_crpr_mode must be pin or transition. 0438 Variables.tcl:187 $var_name value must be 0 or 1. 0439 CmdUtil.tcl:209 unsupported object type $list_type. 0440 Sta.tcl:158 -from/-to arguments not supported with -of_objects. 0441 Sta.tcl:286 unsupported -filter expression. 0442 DelayCalc.tcl:148 $cmd missing -from argument. 0443 DelayCalc.tcl:153 $cmd missing -to argument. 0444 DelayCalc.tcl:158 $cmd delay is not a float. 0445 DelayCalc.tcl:163 set_annotated_delay -cell and -net options are mutually excluive. 0446 DelayCalc.tcl:169 $cmd pin [get_full_name $pin] is not attached to instance [get_full_name $inst]. 0447 DelayCalc.tcl:174 $cmd pin [get_full_name $pin] is not attached to instance [get_full_name $inst] 0448 DelayCalc.tcl:179 $cmd -cell or -net required. 0449 DelayCalc.tcl:243 $cmd missing -from argument. 0450 DelayCalc.tcl:252 $cmd -clock must be rise or fall. 0451 DelayCalc.tcl:259 $cmd missing -to argument. 0452 DelayCalc.tcl:274 $cmd missing -setup|-hold|-recovery|-removal check type.. 0453 DelayCalc.tcl:282 $cmd check_value is not a float. 0454 Sdc.tcl:1472 the -all and -name options are mutually exclusive. 0455 Sdc.tcl:1475 either -all or -name options must be specified. 0456 Sdc.tcl:1483 one of -logically_exclusive, -physically_exclusive or -asynchronous is required. 0457 Sdc.tcl:1486 the keywords -logically_exclusive, -physically_exclusive and -asynchronous are mutually exclusive. 0458 Sdc.tcl:1598 -source '[$pin path_name]' is not a clock pin. 0459 Sdc.tcl:1866 -from/-to must be used together. 0460 Sdc.tcl:1886 -rise, -fall options not allowed for single clock uncertainty. 0461 Sdc.tcl:1987 missing -from, -rise_from or -fall_from argument. 0462 Sdc.tcl:1999 missing -to, -rise_to or -fall_to argument. 0463 Sdc.tcl:2230 -from/-to hierarchical instance not supported. 0464 Sdc.tcl:2632 $cmd command failed. 0465 Sdc.tcl:2639 positional arguments not supported. 0466 Sdc.tcl:2643 -from, -through or -to required. 0467 CmdArgs.tcl:108 unsupported object type $object_type. 0468 CmdArgs.tcl:405 $corner_name is not the name of process corner. 0469 CmdArgs.tcl:410 -corner keyword required with multi-corner analysis. 0470 CmdArgs.tcl:425 $corner_name is not the name of process corner. 0471 CmdArgs.tcl:430 missing -corner arg. 0472 CmdArgs.tcl:441 $corner_name is not the name of process corner. 0473 CmdArgs.tcl:458 $corner_name is not the name of process corner. 0474 CmdArgs.tcl:483 both -min and -max specified. 0475 CmdArgs.tcl:497 both -min and -max specified. 0476 CmdArgs.tcl:524 only one of -early and -late can be specified. 0477 CmdArgs.tcl:530 -early or -late must be specified. 0478 CmdArgs.tcl:537 both -early and -late specified. 0479 CmdArgs.tcl:552 $arg_name must be a single library. 0480 CmdArgs.tcl:558 $arg_name type '$object_type' is not a library. 0481 CmdArgs.tcl:563 library '$arg' not found. 0482 CmdArgs.tcl:580 $arg_name must be a single lib cell. 0483 CmdArgs.tcl:636 $arg_name must be a single instance. 0484 CmdArgs.tcl:642 $arg_name type '$object_type' is not an instance. 0485 CmdArgs.tcl:647 instance '$arg' not found. 0486 CmdArgs.tcl:666 $arg_name type '$object_type' is not an instance. 0487 CmdArgs.tcl:673 instance '$arg' not found. 0488 CmdArgs.tcl:734 $arg_name type '$object_type' is not a pin or port. 0489 CmdArgs.tcl:741 pin '$arg' not found. 0490 CmdArgs.tcl:761 $arg_name type '$object_type' is not a port. 0491 Property.tcl:32 $cmd object is null. 0492 Property.tcl:37 $cmd $type_key must be specified with object name argument. 0493 Property.tcl:80 get_property $object is not an object. 0494 Property.tcl:107 $object_type not supported. 0495 Property.tcl:110 $object_type '$object_name' not found. 0496 WritePathSpice.tcl:35 Directory $spice_dir not found. 0497 WritePathSpice.tcl:38 $spice_dir is not a directory. 0498 WritePathSpice.tcl:41 Cannot write in $spice_dir. 0499 WritePathSpice.tcl:44 No -spice_directory specified. 0500 WritePathSpice.tcl:50 -lib_subckt_file $lib_subckt_file is not readable. 0501 WritePathSpice.tcl:53 No -lib_subckt_file specified. 0502 WritePathSpice.tcl:59 -model_file $model_file is not readable. 0503 WritePathSpice.tcl:62 No -model_file specified. 0504 WritePathSpice.tcl:68 No -power specified. 0505 WritePathSpice.tcl:74 No -ground specified. 0506 WritePathSpice.tcl:78 No -path_args specified. 0507 WritePathSpice.tcl:83 No paths found for -path_args $path_args. 0508 Search.tcl:788 -min and -max cannot both be specified. 0509 Search.tcl:808 pin '$pin_arg' is hierarchical. 0510 Search.tcl:874 -format $format not recognized. 0511 Sdc.tcl:73 cannot open '$filename'. 0512 Sdc.tcl:128 incomplete command at end of file. 0513 Sdc.tcl:212 hierarchy separator must be one of '$sdc_dividers'. 0514 Sdc.tcl:259 unknown unit $unit '$suffix'. 0515 CmdUtil.tcl:161 unknown $unit unit '$suffix'. 0516 Sdc.tcl:543 unsupported instance -filter expression. 0517 Sdc.tcl:928 unsupported pin -filter expression. 0518 Sdc.tcl:1004 unsupported port -filter expression. 0519 Sdc.tcl:1037 -add requires -name. 0520 Sdc.tcl:1042 -name or port_pin_list must be specified. 0521 Sdc.tcl:1050 missing -period argument. 0522 Sdc.tcl:1056 -waveform edge_list must have an even number of edge times. 0523 Sdc.tcl:1126 empty ports/pins/nets argument. 0524 Sdc.tcl:1134 -add requires -name. 0525 Sdc.tcl:1139 name or port_pin_list must be specified. 0526 Sdc.tcl:1146 missing -source argument. 0527 Sdc.tcl:1161 -master_clock argument empty. 0528 Sdc.tcl:1164 -add requireds -master_clock. 0529 Sdc.tcl:1168 -multiply_by and -divide_by options are exclusive. 0530 Sdc.tcl:1172 -divide_by is not an integer greater than one. 0531 Sdc.tcl:1175 -combinational implies -divide_by 1. 0532 Sdc.tcl:1180 -multiply_by is not an integer greater than one. 0533 Sdc.tcl:1186 -duty_cycle is not a float between 0 and 100. 0534 Sdc.tcl:1192 -edges only supported for three edges. 0535 Sdc.tcl:1198 edges times are not monotonically increasing. 0536 Sdc.tcl:1207 -edge_shift length does not match -edges length. 0537 Sdc.tcl:1213 missing -multiply_by, -divide_by, -combinational or -edges argument. 0538 Sdc.tcl:1221 cannot specify -invert without -multiply_by, -divide_by or -combinational. 0539 Sdc.tcl:1227 -duty_cycle requires -multiply_by value. 0545 Sdc.tcl:1287 group_path command failed. 0546 Sdc.tcl:1294 positional arguments not supported. 0547 Sdc.tcl:1298 -from, -through or -to required. 0548 Sdc.tcl:1304 -name and -default are mutually exclusive. 0549 Sdc.tcl:1306 -name or -default option is required. 0550 Sdc.tcl:1347 cannot specify both -high and -low. 0551 Sdc.tcl:1355 missing -setup or -hold argument. 0552 Sdc.tcl:1369 -high and -low only permitted for pins and instances. 0553 Sdc.tcl:1376 -high and -low only permitted for pins and instances. 0554 Sdc.tcl:1419 one of -logically_exclusive, -physically_exclusive or -asynchronous is required. 0555 Sdc.tcl:1422 the keywords -logically_exclusive, -physically_exclusive and -asynchronous are mutually exclusive. 0556 Sdc.tcl:1550 -source '[get_full_name $pin]' is not a clock pin. 0557 Sdc.tcl:1557 -early/-late is only allowed with -source. 0558 Sdc.tcl:1630 set_sense -type clock|data 0559 Sdc.tcl:1699 transition time can not be specified for virtual clocks. 0560 Sdc.tcl:1732 missing uncertainty value. 0561 Sdc.tcl:1780 -from/-to must be used together. 0562 Sdc.tcl:1800 -rise, -fall options not allowed for single clock uncertainty. 0563 Sdc.tcl:1927 missing -from, -rise_from or -fall_from argument. 0564 Sdc.tcl:1939 missing -to, -rise_to or -fall_to argument. 0565 Sdc.tcl:2071 -from/-to hierarchical instance not supported. 0566 Sdc.tcl:2103 pin '[get_full_name $inst]${hierarchy_separator}${port_name}' not found. 0567 Sdc.tcl:2144 pin '[get_name $cell]${hierarchy_separator}${port_name}' not found. 0568 Sdc.tcl:2439 missing delay argument. 0569 Sdc.tcl:2570 missing path multiplier argument. 0570 Sdc.tcl:2582 cannot use -start with -end. 0571 Sdc.tcl:2752 value must be 0, zero, 1, one, rise, rising, fall, or falling. 0572 Sdc.tcl:2821 cell '$lib_name:$cell_name' not found. 0573 Sdc.tcl:2827 '$cell_name' not found. 0574 Sdc.tcl:2831 missing -lib_cell argument. 0575 Sdc.tcl:2839 port '$to_port_name' not found. 0576 Sdc.tcl:2851 -pin argument required for cells with multiple outputs. 0577 Sdc.tcl:2866 port '$from_port_name' not found. 0578 Sdc.tcl:3079 port '[get_name $port]' is not an input. 0579 Sdc.tcl:3453 operating condition '$op_cond_name' not found. 0580 Sdc.tcl:3471 operating condition '$op_cond_name' not found. 0581 Sdc.tcl:3485 -analysis_type must be single, bc_wc or on_chip_variation. 0582 Sdc.tcl:3510 mode must be top, enclosed or segmented. 0583 Sdc.tcl:3525 no wire load model specified. 0584 Sdc.tcl:3586 wire load selection group '$selection_name' not found. 0585 Sdc.tcl:3717 no default operating conditions found. 0586 NetworkEdit.tcl:99 unsupported object type $object_type. 0587 NetworkEdit.tcl:198 unsupported object type $object_type. 0588 NetworkEdit.tcl:216 unsupported object type $object_type. 0589 CmdUtil.tcl:226 unknown namespace $namespc. 0590 Network.tcl:35 instance $instance_path not found. 0591 Network.tcl:241 net $net_path not found. 0592 Network.tcl:244 net $net_path not found. 0593 Link.tcl:34 missing top_cell_name argument and no current_design. 0594 DelayNormal1.cc:203 unknown early/late value. 0595 DelayNormal2.cc:378 unknown early/late value. 0596 Sim.cc:210 unknown function operator 0597 EstimateParasitics.cc:188 load pin not leaf or top level 0600 Sdc.tcl:2284 '$args' ignored. 0601 Sdc.tcl:2913 set_fanout_load not supported. 0602 Sdc.tcl:3385 no valid objects specified for $key. 0604 Sdc.tcl:281 unknown $unit prefix '$prefix'. 0605 Sdc.tcl:3547 wire load model '$model_name' not found. 0606 Property.tcl:77 get_property unsupported object type $object_type. 0607 StaTcl.i:4308 unknown report path field %s 0608 StaTcl.i:4320 unknown report path field %s 0609 Search.tcl:421 -all_violators is deprecated. Use -violators 0610 Search.tcl:501 -max_transition deprecated. Use -max_slew. 0611 Search.tcl:506 -min_transition deprecated. Use -min_slew. 0612 Sdf.tcl:41 -cond_use must be min, max or min_max. 0616 Search.tcl:1018 specify one of -setup and -hold. 0617 Sdf.tcl:50 -analysis_type is deprecated. Use set_operating_conditions -analysis_type. 0618 DmpCeff.cc:1581 parasitic Pi model has NaNs. 0619 PathEnum.cc:474 path diversion missing edge. 0620 PathVertex.cc:236 missing arrivals. 0621 PathVertex.cc:250 missing arrivals. 0622 PathVertex.cc:279 missing requireds. 0623 PathVertexRep.cc:153 missing arrivals. 0624 PathVertexRep.cc:150 missing arrivals 0701 LibertyWriter.cc:416 %s/%s/%s timing model not supported. 0702 LibertyWriter.cc:436 3 axis table models not supported. 0703 LibertyWriter.cc:576 %s/%s/%s timing arc type %s not supported. 0704 LibertyWriter.cc:289 %s/%s bundled ports not supported. 0705 Liberty.cc:795 Liberty cell %s/%s for corner %s/%s not found. 0706 Parasitics.tcl:70 read_spef -increment is deprecated. 0710 LumpedCapDelayCalc.cc:169 gate delay input variable is NaN 0800 VcdReader.cc:109 unhandled vcd command. 0801 VcdReader.cc:145 timescale syntax error. 0802 VcdReader.cc:159 Unknown timescale unit. 0804 VcdReader.cc:200 Variable syntax error. 0805 Vcd.cc:172 Unknown variable %s ID %s 0806 ReadVcdActivities.cc:247 clock %s vcd period %s differs from SDC clock period %s 0807 Sdc.tcl:394 only one of -cells, -data_pins, -clock_pins, -async_pins, -output_pins are suppported. 0810 MakeTimingModel.cc:189 clock %s pin %s is inside model block. 0900 LibertyReader.cc:2840 level_shifter_type must be HL, LH, or HL_LH 0901 LibertyReader.cc:2876 switch_cell_type must be coarse_grain or fine_grain 0902 LibertyReader.cc:2464 unsupported model axis. 0903 LibertyReader.cc:4219 %s group not in timing group. 0904 LibertyReader.cc:2447 receiver_capacitance group not in timing or pin group. 0906 LibertyReader.cc:4112 unsupported model axis. 0907 LibertyReader.cc:2492 output_current_%s group not in timing group. 0908 LibertyReader.cc:2591 vector reference_time not found. 0912 LibertyReader.cc:2589 vector index_1 and index_2 must have exactly one value. 0913 LibertyReader.cc:2531 output current waveform %.2e %.2e not found. 0914 LibertyReader.cc:2624 normalized_driver_waveform variable_2 must be normalized_voltage 0915 LibertyReader.cc:2627 normalized_driver_waveform variable_1 must be input_net_transition