# See LICENSE for licensing information. # # Copyright (c) 2016-2021 Regents of the University of California and The Board # of Regents for the Oklahoma Agricultural and Mechanical College # (acting for and on behalf of Oklahoma State University) # All rights reserved. # import sys from tech import drc, parameter import debug from base import design import math from math import log,sqrt,ceil from base import vector from sram_factory import factory from globals import OPTS class multibank(design): """ Dynamically generated a single bank including bitcell array, hierarchical_decoder, precharge, (optional column_mux and column decoder), write driver and sense amplifiers. This module includes the tristate and bank select logic. """ def __init__(self, name, word_size, num_words, words_per_row, num_banks=1): super().__init__(name) debug.info(2, "create sram of size {0} with {1} words".format(word_size,num_words)) self.word_size = word_size self.num_words = num_words self.words_per_row = words_per_row self.num_banks = num_banks # The local control signals are gated when we have bank select logic, # so this prefix will be added to all of the input signals to create # the internal gated signals. if self.num_banks>1: self.prefix="gated_" else: self.prefix="" self.compute_sizes() self.add_pins() self.add_modules() self.create_instances() self.setup_layout_constraints() # FIXME: Move this to the add modules function self.add_bank_select() self.route_layout() # Can remove the following, but it helps for debug! self.add_lvs_correspondence_points() # Remember the bank center for further placement self.bank_center=self.offset_all_coordinates().scale(-1,-1) self.DRC_LVS() def add_pins(self): """ Adding pins for Bank module""" for i in range(self.word_size): self.add_pin("dout_{0}".format(i),"OUT") for i in range(self.word_size): self.add_pin("bank_din_{0}".format(i),"IN") for i in range(self.addr_size): self.add_pin("a_{0}".format(i),"INPUT") # For more than one bank, we have a bank select and name # the signals gated_*. if self.num_banks > 1: self.add_pin("bank_sel","INPUT") for pin in ["s_en","w_en","tri_en_bar","tri_en", "clk_buf_bar","clk_buf"]: self.add_pin(pin,"INPUT") self.add_pin("vdd","POWER") self.add_pin("gnd","GROUND") def route_layout(self): """ Create routing amoung the modules """ self.route_central_bus() self.route_precharge_to_bitcell_array() self.route_col_mux_to_bitcell_array() self.route_sense_amp_to_col_mux_or_bitcell_array() #self.route_sense_amp_to_trigate() #self.route_tri_gate_out() self.route_sense_amp_out() self.route_wordline_driver() self.route_write_driver() self.route_row_decoder() self.route_column_address_lines() self.route_control_lines() self.add_control_pins() if self.num_banks > 1: self.route_bank_select() self.route_supplies() def create_instances(self): """ Add modules. The order should not matter! """ # Above the bitcell array self.add_bitcell_array() self.add_precharge_array() # Below the bitcell array self.add_column_mux_array() self.add_sense_amp_array() self.add_write_driver_array() # Not needed for single bank #self.add_tri_gate_array() # To the left of the bitcell array self.add_row_decoder() self.add_wordline_driver() self.add_column_decoder() def compute_sizes(self): """ Computes the required sizes to create the bank """ self.num_cols = int(self.words_per_row*self.word_size) self.num_rows = int(self.num_words / self.words_per_row) self.row_addr_size = int(log(self.num_rows, 2)) self.col_addr_size = int(log(self.words_per_row, 2)) self.addr_size = self.col_addr_size + self.row_addr_size debug.check(self.num_rows*self.num_cols==self.word_size*self.num_words,"Invalid bank sizes.") debug.check(self.addr_size==self.col_addr_size + self.row_addr_size,"Invalid address break down.") # Width for the vdd/gnd rails self.supply_rail_width = 4*self.m2_width # FIXME: This spacing should be width dependent... self.supply_rail_pitch = self.supply_rail_width + 4*self.m2_space # Number of control lines in the bus self.num_control_lines = 6 # The order of the control signals on the control bus: self.input_control_signals = ["clk_buf", "tri_en_bar", "tri_en", "clk_buf_bar", "w_en", "s_en"] # These will be outputs of the gaters if this is multibank, if not, normal signals. if self.num_banks > 1: self.control_signals = ["gated_"+str for str in self.input_control_signals] else: self.control_signals = self.input_control_signals # The central bus is the column address (one hot) and row address (binary) if self.col_addr_size>0: self.num_col_addr_lines = 2**self.col_addr_size else: self.num_col_addr_lines = 0 # The width of this bus is needed to place other modules (e.g. decoder) # A width on each side too self.central_bus_width = self.m2_pitch * self.num_control_lines + 2*self.m2_width # A space for wells or jogging m2 self.m2_gap = max(2*drc("pwell_to_nwell"] + drc["well_enclose_active"), 2*self.m2_pitch) def add_modules(self): """ Add all the modules using the class loader """ self.tri = self.mod_tri_gate() self.bitcell = self.mod_bitcell() self.bitcell_array = self.mod_bitcell_array(cols=self.num_cols, rows=self.num_rows) self.precharge_array = self.mod_precharge_array(columns=self.num_cols) if self.col_addr_size > 0: self.column_mux_array = self.mod_column_mux_array(columns=self.num_cols, word_size=self.word_size) self.sense_amp_array = self.mod_sense_amp_array(word_size=self.word_size, words_per_row=self.words_per_row) if self.write_size: self.write_mask_driver_array = self.mod_write_mask_driver_array(columns=self.num_cols, word_size=self.word_size, write_size=self.write_size) else: self.write_driver_array = self.mod_write_driver_array(columns=self.num_cols, word_size=self.word_size) self.row_decoder = self.mod_decoder(rows=self.num_rows) self.tri_gate_array = self.mod_tri_gate_array(columns=self.num_cols, word_size=self.word_size) self.wordline_driver = self.mod_wordline_driver(rows=self.num_rows) self.inv = pinv() if(self.num_banks > 1): self.bank_select = self.mod_bank_select() def add_bitcell_array(self): """ Adding Bitcell Array """ self.bitcell_array_inst=self.add_inst(name="bitcell_array", mod=self.bitcell_array, offset=vector(0,0)) temp = [] for i in range(self.num_cols): temp.append("bl_{0}".format(i)) temp.append("br_{0}".format(i)) for j in range(self.num_rows): temp.append("wl_{0}".format(j)) temp.extend(["vdd", "gnd"]) self.connect_inst(temp) def add_precharge_array(self): """ Adding Precharge """ # The wells must be far enough apart # The enclosure is for the well and the spacing is to the bitcell wells y_offset = self.bitcell_array.height + self.m2_gap self.precharge_array_inst=self.add_inst(name="precharge_array", mod=self.precharge_array, offset=vector(0,y_offset)) temp = [] for i in range(self.num_cols): temp.append("bl_{0}".format(i)) temp.append("br_{0}".format(i)) temp.extend([self.prefix+"clk_buf_bar", "vdd"]) self.connect_inst(temp) def add_column_mux_array(self): """ Adding Column Mux when words_per_row > 1 . """ if self.col_addr_size > 0: self.column_mux_height = self.column_mux_array.height + self.m2_gap else: self.column_mux_height = 0 return y_offset = self.column_mux_height self.col_mux_array_inst=self.add_inst(name="column_mux_array", mod=self.column_mux_array, offset=vector(0,y_offset).scale(-1,-1)) temp = [] for i in range(self.num_cols): temp.append("bl_{0}".format(i)) temp.append("br_{0}".format(i)) for k in range(self.words_per_row): temp.append("sel_{0}".format(k)) for j in range(self.word_size): temp.append("bl_out_{0}".format(j)) temp.append("br_out_{0}".format(j)) temp.append("gnd") self.connect_inst(temp) def add_sense_amp_array(self): """ Adding Sense amp """ y_offset = self.column_mux_height + self.sense_amp_array.height + self.m2_gap self.sense_amp_array_inst=self.add_inst(name="sense_amp_array", mod=self.sense_amp_array, offset=vector(0,y_offset).scale(-1,-1)) temp = [] for i in range(self.word_size): temp.append("sa_out_{0}".format(i)) if self.words_per_row == 1: temp.append("bl_{0}".format(i)) temp.append("br_{0}".format(i)) else: temp.append("bl_out_{0}".format(i)) temp.append("br_out_{0}".format(i)) temp.extend([self.prefix+"s_en", "vdd", "gnd"]) self.connect_inst(temp) def add_write_driver_array(self): """ Adding Write Driver """ y_offset = self.sense_amp_array.height + self.column_mux_height \ + self.m2_gap + self.write_driver_array.height self.write_driver_array_inst=self.add_inst(name="write_driver_array", mod=self.write_driver_array, offset=vector(0,y_offset).scale(-1,-1)) temp = [] for i in range(self.word_size): temp.append("bank_din_{0}".format(i)) for i in range(self.word_size): if (self.words_per_row == 1): temp.append("bl_{0}".format(i)) temp.append("br_{0}".format(i)) else: temp.append("bl_out_{0}".format(i)) temp.append("br_out_{0}".format(i)) temp.extend([self.prefix+"w_en", "vdd", "gnd"]) self.connect_inst(temp) def add_tri_gate_array(self): """ data tri gate to drive the data bus """ y_offset = self.sense_amp_array.height+self.column_mux_height \ + self.m2_gap + self.tri_gate_array.height self.tri_gate_array_inst=self.add_inst(name="tri_gate_array", mod=self.tri_gate_array, offset=vector(0,y_offset).scale(-1,-1)) temp = [] for i in range(self.word_size): temp.append("sa_out_{0}".format(i)) for i in range(self.word_size): temp.append("dout_{0}".format(i)) temp.extend([self.prefix+"tri_en", self.prefix+"tri_en_bar", "vdd", "gnd"]) self.connect_inst(temp) def add_row_decoder(self): """ Add the hierarchical row decoder """ # The address and control bus will be in between decoder and the main memory array # This bus will route address bits to the decoder input and column mux inputs. # The wires are actually routed after we placed the stuff on both sides. # The predecoder is below the x-axis and the main decoder is above the x-axis # The address flop and decoder are aligned in the x coord. x_offset = -(self.row_decoder.width + self.central_bus_width + self.wordline_driver.width) self.row_decoder_inst=self.add_inst(name="row_decoder", mod=self.row_decoder, offset=vector(x_offset,0)) temp = [] for i in range(self.row_addr_size): temp.append("A_{0}".format(i+self.col_addr_size)) for j in range(self.num_rows): temp.append("dec_out_{0}".format(j)) temp.extend(["vdd", "gnd"]) self.connect_inst(temp) def add_wordline_driver(self): """ Wordline Driver """ # The wordline driver is placed to the right of the main decoder width. x_offset = -(self.central_bus_width + self.wordline_driver.width) + self.m2_pitch self.wordline_driver_inst=self.add_inst(name="wordline_driver", mod=self.wordline_driver, offset=vector(x_offset,0)) temp = [] for i in range(self.num_rows): temp.append("dec_out_{0}".format(i)) for i in range(self.num_rows): temp.append("wl_{0}".format(i)) temp.append(self.prefix+"clk_buf") temp.append("vdd") temp.append("gnd") self.connect_inst(temp) def add_column_decoder_module(self): """ Create a 2:4 or 3:8 column address decoder. """ # Place the col decoder right aligned with row decoder x_off = -(self.central_bus_width + self.wordline_driver.width + self.col_decoder.width) y_off = -(self.col_decoder.height + 2*drc("well_to_well")) self.col_decoder_inst=self.add_inst(name="col_address_decoder", mod=self.col_decoder, offset=vector(x_off,y_off)) temp = [] for i in range(self.col_addr_size): temp.append("A_{0}".format(i)) for j in range(self.num_col_addr_lines): temp.append("sel_{0}".format(j)) temp.extend(["vdd", "gnd"]) self.connect_inst(temp) def add_column_decoder(self): """ Create a decoder to decode column select lines. This could be an inverter/buffer for 1:2, 2:4 decoder, or 3:8 decoder. """ if self.col_addr_size == 0: return elif self.col_addr_size == 1: self.col_decoder = pinvbuf(height=self.mod_dff.height) self.add_mod(self.col_decoder) elif self.col_addr_size == 2: self.col_decoder = self.row_decoder.pre2_4 elif self.col_addr_size == 3: self.col_decoder = self.row_decoder.pre3_8 else: # No error checking before? debug.error("Invalid column decoder?",-1) self.add_column_decoder_module() def add_bank_select(self): """ Instantiate the bank select logic. """ if not self.num_banks > 1: return x_off = -(self.row_decoder.width + self.central_bus_width + self.wordline_driver.width) if self.col_addr_size > 0: y_off = min(self.col_decoder_inst.by(), self.col_mux_array_inst.by()) else: y_off = self.row_decoder_inst.by() y_off -= (self.bank_select.height + drc("well_to_well")) self.bank_select_pos = vector(x_off,y_off) self.bank_select_inst = self.add_inst(name="bank_select", mod=self.bank_select, offset=self.bank_select_pos) temp = [] temp.extend(self.input_control_signals) temp.append("bank_sel") temp.extend(self.control_signals) temp.extend(["vdd", "gnd"]) self.connect_inst(temp) def route_supplies(self): """ Propagate all vdd/gnd pins up to this level for all modules """ for inst in self.insts: self.copy_power_pins(inst,"vdd") self.copy_power_pins(inst,"gnd") def route_bank_select(self): """ Route the bank select logic. """ for input_name in self.input_control_signals+["bank_sel"]: self.copy_layout_pin(self.bank_select_inst, input_name) for gated_name in self.control_signals: # Connect the inverter output to the central bus out_pos = self.bank_select_inst.get_pin(gated_name).rc() bus_pos = vector(self.bus_xoffset[gated_name], out_pos.y) self.add_path("m3",[out_pos, bus_pos]) self.add_via_center(layers=self.m2_stack, offset=bus_pos, rotate=90) self.add_via_center(layers=self.m1_stack, offset=out_pos, rotate=90) self.add_via_center(layers=self.m2_stack, offset=out_pos, rotate=90) def setup_layout_constraints(self): """ After the modules are instantiated, find the dimensions for the control bus, power ring, etc. """ #The minimum point is either the bottom of the address flops, #the column decoder (if there is one) or the tristate output #driver. # Leave room for the output below the tri gate. #tri_gate_min_y_offset = self.tri_gate_array_inst.by() - 3*self.m2_pitch write_driver_min_y_offset = self.write_driver_array_inst.by() - 3*self.m2_pitch row_decoder_min_y_offset = self.row_decoder_inst.by() if self.col_addr_size > 0: col_decoder_min_y_offset = self.col_decoder_inst.by() else: col_decoder_min_y_offset = row_decoder_min_y_offset if self.num_banks>1: # The control gating logic is below the decoder # Min of the control gating logic and tri gate. self.min_y_offset = min(col_decoder_min_y_offset - self.bank_select.height, write_driver_min_y_offset) else: # Just the min of the decoder logic logic and tri gate. self.min_y_offset = min(col_decoder_min_y_offset, write_driver_min_y_offset) # The max point is always the top of the precharge bitlines # Add a vdd and gnd power rail above the array self.max_y_offset = self.precharge_array_inst.uy() + 3*self.m1_width self.max_x_offset = self.bitcell_array_inst.ur().x + 3*self.m1_width self.min_x_offset = self.row_decoder_inst.lx() # # Create the core bbox for the power rings ur = vector(self.max_x_offset, self.max_y_offset) ll = vector(self.min_x_offset, self.min_y_offset) self.core_bbox = [ll, ur] self.height = ur.y - ll.y self.width = ur.x - ll.x def route_central_bus(self): """ Create the address, supply, and control signal central bus lines. """ # Overall central bus width. It includes all the column mux lines, # and control lines. # The bank is at (0,0), so this is to the left of the y-axis. # 2 pitches on the right for vias/jogs to access the inputs control_bus_offset = vector(-self.m2_pitch * self.num_control_lines - self.m2_width, 0) control_bus_length = self.bitcell_array_inst.uy() self.bus_xoffset = self.create_vertical_bus(layer="m2", pitch=self.m2_pitch, offset=control_bus_offset, names=self.control_signals, length=control_bus_length) def route_precharge_to_bitcell_array(self): """ Routing of BL and BR between pre-charge and bitcell array """ for i in range(self.num_cols): precharge_bl = self.precharge_array_inst.get_pin("bl_{}".format(i)).bc() precharge_br = self.precharge_array_inst.get_pin("br_{}".format(i)).bc() bitcell_bl = self.bitcell_array_inst.get_pin("bl_{}".format(i)).uc() bitcell_br = self.bitcell_array_inst.get_pin("br_{}".format(i)).uc() yoffset = 0.5*(precharge_bl.y+bitcell_bl.y) self.add_path("m2",[precharge_bl, vector(precharge_bl.x,yoffset), vector(bitcell_bl.x,yoffset), bitcell_bl]) self.add_path("m2",[precharge_br, vector(precharge_br.x,yoffset), vector(bitcell_br.x,yoffset), bitcell_br]) def route_col_mux_to_bitcell_array(self): """ Routing of BL and BR between col mux and bitcell array """ # Only do this if we have a column mux! if self.col_addr_size==0: return for i in range(self.num_cols): col_mux_bl = self.col_mux_array_inst.get_pin("bl_{}".format(i)).uc() col_mux_br = self.col_mux_array_inst.get_pin("br_{}".format(i)).uc() bitcell_bl = self.bitcell_array_inst.get_pin("bl_{}".format(i)).bc() bitcell_br = self.bitcell_array_inst.get_pin("br_{}".format(i)).bc() yoffset = 0.5*(col_mux_bl.y+bitcell_bl.y) self.add_path("m2",[col_mux_bl, vector(col_mux_bl.x,yoffset), vector(bitcell_bl.x,yoffset), bitcell_bl]) self.add_path("m2",[col_mux_br, vector(col_mux_br.x,yoffset), vector(bitcell_br.x,yoffset), bitcell_br]) def route_sense_amp_to_col_mux_or_bitcell_array(self): """ Routing of BL and BR between sense_amp and column mux or bitcell array """ for i in range(self.word_size): sense_amp_bl = self.sense_amp_array_inst.get_pin("bl_{}".format(i)).uc() sense_amp_br = self.sense_amp_array_inst.get_pin("br_{}".format(i)).uc() if self.col_addr_size>0: # Sense amp is connected to the col mux connect_bl = self.col_mux_array_inst.get_pin("bl_out_{}".format(i)).bc() connect_br = self.col_mux_array_inst.get_pin("br_out_{}".format(i)).bc() else: # Sense amp is directly connected to the bitcell array connect_bl = self.bitcell_array_inst.get_pin("bl_{}".format(i)).bc() connect_br = self.bitcell_array_inst.get_pin("br_{}".format(i)).bc() yoffset = 0.5*(sense_amp_bl.y+connect_bl.y) self.add_path("m2",[sense_amp_bl, vector(sense_amp_bl.x,yoffset), vector(connect_bl.x,yoffset), connect_bl]) self.add_path("m2",[sense_amp_br, vector(sense_amp_br.x,yoffset), vector(connect_br.x,yoffset), connect_br]) def route_sense_amp_to_trigate(self): """ Routing of sense amp output to tri_gate input """ for i in range(self.word_size): # Connection of data_out of sense amp to data_in tri_gate_in = self.tri_gate_array_inst.get_pin("in_{}".format(i)).lc() sa_data_out = self.sense_amp_array_inst.get_pin("data_{}".format(i)).bc() self.add_via_center(layers=self.m2_stack, offset=tri_gate_in) self.add_via_center(layers=self.m2_stack, offset=sa_data_out) self.add_path("m3",[sa_data_out,tri_gate_in]) def route_sense_amp_out(self): """ Add pins for the sense amp output """ for i in range(self.word_size): data_pin = self.sense_amp_array_inst.get_pin("data_{}".format(i)) self.add_layout_pin_rect_center(text="dout_{}".format(i), layer=data_pin.layer, offset=data_pin.center(), height=data_pin.height(), width=data_pin.width()), def route_tri_gate_out(self): """ Metal 3 routing of tri_gate output data """ for i in range(self.word_size): data_pin = self.tri_gate_array_inst.get_pin("out_{}".format(i)) self.add_layout_pin_rect_center(text="dout_{}".format(i), layer=data_pin.layer, offset=data_pin.center(), height=data_pin.height(), width=data_pin.width()), def route_row_decoder(self): """ Routes the row decoder inputs and supplies """ # Create inputs for the row address lines for i in range(self.row_addr_size): addr_idx = i + self.col_addr_size decoder_name = "a_{}".format(i) addr_name = "a_{}".format(addr_idx) self.copy_layout_pin(self.row_decoder_inst, decoder_name, addr_name) def route_write_driver(self): """ Connecting write driver """ for i in range(self.word_size): data_name = "data_{}".format(i) din_name = "bank_din_{}".format(i) self.copy_layout_pin(self.write_driver_array_inst, data_name, din_name) def route_wordline_driver(self): """ Connecting Wordline driver output to Bitcell WL connection """ # we don't care about bends after connecting to the input pin, so let the path code decide. for i in range(self.num_rows): # The pre/post is to access the pin from "outside" the cell to avoid DRCs decoder_out_pos = self.row_decoder_inst.get_pin("decode_{}".format(i)).rc() driver_in_pos = self.wordline_driver_inst.get_pin("in_{}".format(i)).lc() mid1 = decoder_out_pos.scale(0.5,1)+driver_in_pos.scale(0.5,0) mid2 = decoder_out_pos.scale(0.5,0)+driver_in_pos.scale(0.5,1) self.add_path("m1", [decoder_out_pos, mid1, mid2, driver_in_pos]) # The mid guarantees we exit the input cell to the right. driver_wl_pos = self.wordline_driver_inst.get_pin("wl_{}".format(i)).rc() bitcell_wl_pos = self.bitcell_array_inst.get_pin("wl_{}".format(i)).lc() mid1 = driver_wl_pos.scale(0.5,1)+bitcell_wl_pos.scale(0.5,0) mid2 = driver_wl_pos.scale(0.5,0)+bitcell_wl_pos.scale(0.5,1) self.add_path("m1", [driver_wl_pos, mid1, mid2, bitcell_wl_pos]) def route_column_address_lines(self): """ Connecting the select lines of column mux to the address bus """ if not self.col_addr_size>0: return if self.col_addr_size == 1: # Connect to sel[0] and sel[1] decode_names = ["Zb", "Z"] # The Address LSB self.copy_layout_pin(self.col_decoder_inst, "A", "a[0]") elif self.col_addr_size > 1: decode_names = [] for i in range(self.num_col_addr_lines): decode_names.append("out_{}".format(i)) for i in range(self.col_addr_size): decoder_name = "in_{}".format(i) addr_name = "a_{}".format(i) self.copy_layout_pin(self.col_decoder_inst, decoder_name, addr_name) # This will do a quick "river route" on two layers. # When above the top select line it will offset "inward" again to prevent conflicts. # This could be done on a single layer, but we follow preferred direction rules for later routing. top_y_offset = self.col_mux_array_inst.get_pin("sel_{}".format(self.num_col_addr_lines-1)).cy() for (decode_name,i) in zip(decode_names,range(self.num_col_addr_lines)): mux_name = "sel_{}".format(i) mux_addr_pos = self.col_mux_array_inst.get_pin(mux_name).lc() decode_out_pos = self.col_decoder_inst.get_pin(decode_name).center() # To get to the edge of the decoder and one track out delta_offset = self.col_decoder_inst.rx() - decode_out_pos.x + self.m2_pitch if decode_out_pos.y > top_y_offset: mid1_pos = vector(decode_out_pos.x + delta_offset + i*self.m2_pitch,decode_out_pos.y) else: mid1_pos = vector(decode_out_pos.x + delta_offset + (self.num_col_addr_lines-i)*self.m2_pitch,decode_out_pos.y) mid2_pos = vector(mid1_pos.x,mux_addr_pos.y) #self.add_wire(self.m1_stack,[decode_out_pos, mid1_pos, mid2_pos, mux_addr_pos]) self.add_path("m1",[decode_out_pos, mid1_pos, mid2_pos, mux_addr_pos]) def add_lvs_correspondence_points(self): """ This adds some points for easier debugging if LVS goes wrong. These should probably be turned off by default though, since extraction will show these as ports in the extracted netlist. """ # Add the wordline names for i in range(self.num_rows): wl_name = "wl_{}".format(i) wl_pin = self.bitcell_array_inst.get_pin(wl_name) self.add_label(text=wl_name, layer="m1", offset=wl_pin.center()) # Add the bitline names for i in range(self.num_cols): bl_name = "bl_{}".format(i) br_name = "br_{}".format(i) bl_pin = self.bitcell_array_inst.get_pin(bl_name) br_pin = self.bitcell_array_inst.get_pin(br_name) self.add_label(text=bl_name, layer="m2", offset=bl_pin.center()) self.add_label(text=br_name, layer="m2", offset=br_pin.center()) # # Add the data output names to the sense amp output # for i in range(self.word_size): # data_name = "data_{}".format(i) # data_pin = self.sense_amp_array_inst.get_pin(data_name) # self.add_label(text="sa_out_{}".format(i), # layer="m2", # offset=data_pin.center()) # Add labels on the decoder for i in range(self.word_size): data_name = "dec_out_{}".format(i) pin_name = "in_{}".format(i) data_pin = self.wordline_driver_inst.get_pin(pin_name) self.add_label(text=data_name, layer="m1", offset=data_pin.center()) def route_control_lines(self): """ Route the control lines of the entire bank """ # Make a list of tuples that we will connect. # From control signal to the module pin # Connection from the central bus to the main control block crosses # pre-decoder and this connection is in metal3 connection = [] #connection.append((self.prefix+"tri_en_bar", self.tri_gate_array_inst.get_pin("en_bar").lc())) #connection.append((self.prefix+"tri_en", self.tri_gate_array_inst.get_pin("en").lc())) connection.append((self.prefix+"clk_buf_bar", self.precharge_array_inst.get_pin("en").lc())) connection.append((self.prefix+"w_en", self.write_driver_array_inst.get_pin("en").lc())) connection.append((self.prefix+"s_en", self.sense_amp_array_inst.get_pin("en").lc())) for (control_signal, pin_pos) in connection: control_pos = vector(self.bus_xoffset[control_signal].x ,pin_pos.y) self.add_path("m1", [control_pos, pin_pos]) self.add_via_center(layers=self.m1_stack, offset=control_pos, rotate=90) # clk to wordline_driver control_signal = self.prefix+"clk_buf" pin_pos = self.wordline_driver_inst.get_pin("en").uc() mid_pos = pin_pos + vector(0,self.m1_pitch) control_x_offset = self.bus_xoffset[control_signal].x control_pos = vector(control_x_offset + self.m1_width, mid_pos.y) self.add_wire(self.m1_stack,[pin_pos, mid_pos, control_pos]) control_via_pos = vector(control_x_offset, mid_pos.y) self.add_via_center(layers=self.m1_stack, offset=control_via_pos, rotate=90) def add_control_pins(self): """ Add the control signal input pins """ for ctrl in self.control_signals: # xoffsets are the center of the rail x_offset = self.bus_xoffset[ctrl].x - 0.5*self.m2_width if self.num_banks > 1: # it's not an input pin if we have multiple banks self.add_label_pin(text=ctrl, layer="m2", offset=vector(x_offset, self.min_y_offset), width=self.m2_width, height=self.max_y_offset-self.min_y_offset) else: self.add_layout_pin(text=ctrl, layer="m2", offset=vector(x_offset, self.min_y_offset), width=self.m2_width, height=self.max_y_offset-self.min_y_offset) def connect_rail_from_right(self,inst, pin, rail): """ Helper routine to connect an unrotated/mirrored oriented instance to the rails """ in_pin = inst.get_pin(pin).lc() rail_pos = vector(self.rail_1_x_offsets[rail], in_pin.y) self.add_wire(("m3","via2","m2"),[in_pin, rail_pos, rail_pos - vector(0,self.m2_pitch)]) # Bring it up to M2 for M2/M3 routing self.add_via(layers=self.m1_stack, offset=in_pin + self.m1_via.offset, rotate=90) self.add_via(layers=self.m2_stack, offset=in_pin + self.m2m3_via_offset, rotate=90) def connect_rail_from_left(self,inst, pin, rail): """ Helper routine to connect an unrotated/mirrored oriented instance to the rails """ in_pin = inst.get_pin(pin).rc() rail_pos = vector(self.rail_1_x_offsets[rail], in_pin.y) self.add_wire(("m3","via2","m2"),[in_pin, rail_pos, rail_pos - vector(0,self.m2_pitch)]) self.add_via(layers=self.m1_stack, offset=in_pin + self.m1_via.offset, rotate=90) self.add_via(layers=self.m2_stack, offset=in_pin + self.m2m3_via_offset, rotate=90)